background image

ASSEMBLY GUIDE 

GRILL FINAL Assembly

           

Part 

 

Qty

.  

C1

– 

 

C2

– 

Cooking Grate

  1 

C3

– 

Warming Rack

  1 

 

 

 

 

Grease tray

 

 

 

C2

 

C3

 

Step 1

 - With the 

Grill Lid

 open, place the 

Cooking Grate

 

(C1)

into the 

Lower Body

, allowing it to rest on the three brackets 

spaced around the 

Lower Body. 

Be sure the slots in the 

Cooking Grate

 are facing the front of thegrill. Place the  

Warming Rack 

(C2)

 into position by first hooking the center pins into the wind shield, then rotate the warming rack down into position. 

Step 2

 -  Install the 

Grease Tray (C3)

 by sliding the tray onto the 

Grease Tray Rails

 from the rear of the grill. 

Note: 

The 

grease tray rests between the grease tray rail stops. See detail shown in 

Figure A

.

NOTE:

 The 

Cooking Grate

 may 

have sharp edges. Be very careful 
when handling the 

Cooking Grate.

 

You should wear gloves when 
handling the 

Cooking Grate

.

Grease

Tray

Rails

C1 

Slots to 
the front 
of the grill.

Visit 

www.sizzleonthegrill.com/user-forums

 to chat with Patio Bistro

®

 owners just like you!

 

Grease

Tray

Rail Stops

Fig. A

Содержание 11601514 11601559 11601578









Отзывы: