background image

Page 8 

 

Attachment 

Before Attaching the Machine 

 

Before attachment, ALWAYS ensure the following: 
 

 

All safety guards & decals are in good working order and correctly fitted 

 

All blades are correctly fitted, undamaged, and not worn to excess 

 

Lubrication points have been lubricated as per scheduled maintenance period 

 

The engine oil level is correct & has been maintained as per the handbook 

 

Drive belt(s) are in good working order 

 

The tyres are free of damage and inflated to the correct pressure 

 

 

Attaching the Machine 

NOTE: This machine is designed to attach to the towing vehicle through a 50mm diameter ball hitch 
or pin hitch. 
 
1. Reverse the towing vehicle up to the machine. 
 
2. Attach the machine onto th

e towing vehicle’s coupling using either the auto

-lock coupling or 

suitable pin 
hitch. Ensure the hitch is securely attached to the towing vehicle 
 
3. Attach the emergency stop control box to the towing vehicle, in a secure location within easy 
reach by the operator. 

 

4. With the engine OFF, adjust the working height to a suitable level by turning the height adjuster 
on top of the machine. 
 
5. Level the machine to suit the drawbar & cutting height. This is achieved by twisting the link 
connector fitted to the drawbar. When on level ground, the top face of the mower deck (where the 
engine is mounted) should be approximately parallel to the ground. 
 

Operation 

NOTE: 

Ensure that the operator is suitably qualified to use a machine of this nature and that they 

have fully read and understood this manual - they should be aware of all safety aspects relating to 
the safe use of the machine. 
 
Prior to starting work the area to be cut should be checked for dangerous objects such as 
large stones, wood, wire, glass etc. 

 hazardous objects should be removed from the area 

prior to operation with the machine. The location of unmovable or natural hazards such as 

drain covers should be noted, or if necessary ‘marked’, to indicate to the operator that the 

area should either be avoided or additional caution adopted whilst working around the 
hazard. 
 

Содержание FM Series

















Отзывы: