background image

Page 4 

 

Important Safety Information 

Always read this manual before fitting or operating the machine 

 whenever any doubt exists contact your 

dealer or the Chapman Machinery Service Department for advice and assistance. 

 

 

DEFINITIONS 

The following definitions apply throughout this manual:

 

 

WARNING - 

An operating procedure, technique etc., which can result in personal injury or loss of life if 

not observed carefully. 

 

CAUTION  - 

An  operating  procedure,  technique  etc.,  which  can  result  in  damage  to  either  machine  or 

equipment if not observed carefully.

 

 

NOTE 

- An operating procedure, technique etc, which is considered essential to emphasis.

 

 

LEFT & RIGHT HAND

 - This term is applicable to the machine when attached to the towing vehicle and is 

viewed from the rear 

 this also applies to tractor references.

 

 

Safety Information 

 

Do not operate this equipment unless you have studied this manual in full 

 

Only use this machine for its designated task - improper use is both highly dangerous and damaging to 
machine components 

 

Both operators & maintenance fitters should be familiar with the machine and fully aware of dangers 
surrounding improper use or incorrect repairs

 

 

Before starting, carry out a visual check on both machine & towing vehicle as regards functionality, road 
safety & accident prevention rules 

 

Even when using the machine correctly, foreign objects such as stones may be thrown a considerable 
distance. It is imperative that nobody stand within the danger area. If working near roads, buildings children 
or animals provision must be made for containment of ejected material and sufficient warning signs / notices 
placed around the working area 

 

The condition of flails and of machine guards must be checked before beginning the 

day’s 

work. Worn or 

damaged flails must be replaced before you use the machine. Flails must be replaced in pairs to ensure rotor 
balance is maintained.  

 

During checks or repairs, ensure the machine cannot be started by other persons by mistake 

 

Never wear loose clothing which could get caught in rotating equipment 

 

Never carry passengers on the towing vehicle 

 

Never approach the machine until the rotor has stopped rotating 

 

Do not stand near the machine when operating 

 

Damaged or missing safety decals must be replaced immediately 

 

Before leaving the machine unattended, remove the starting key (if applicable) 

 

ENSURE emergency stop switch is SECURELY attached to the towing vehicle and within reach of the operator 
at all times 

Содержание FM Series

















Отзывы: