10
11
Specifications:
(typical @25º C)
Audio Output
Output Impedance:
600 Ohms
Power Requirements:
15VDC @ 0.500A (500mA)
Power Supply:
15VDC @ 800mA
Wire type:
4-pair,
UTP Category 5, 5e or 6
Recommended Max. Cable Length:
350ft.
Dimensions:
Wall Dock (2-gang):
4.88”W x 5.14”H x 1.24”D(front)
Rear Depth: 1.56”
Wall Dock & Keypad (3-gang):
6.73”W x 5.14”H x 1.24”D(front)
Rear Depth: 1.56”
Output Plate (1-gang):
3.15”W x 5.14”H x 1.24”D(front)
Rear Depth: 1.95”
Color:
White
Operating Temperature:
-10ºC to +50ºC
*Specifications subject to change without notice.
Green/White - Left Channel Audio Ground
Green - Left Channel Audio
Orange/White - Right Channel Audio Ground
Blue - IR Signal
Blue/White - Status
Orange- Right - Channel Audio
Brown/White - vDC Ground
Brown - vDC
Top view:
Pin-out
Stripping and Connecting CAT-5 Wire
Blade
Cat5
1.
Place the CAT-5 between the blade and the first notch of the J-110 tool.
CAT-5 cable should be stripped with a proper stripping tool, such as Channel
Vision’s J-110 tool.
Slight
pressure
Rotate
1 turn only
2.
Rotate the tool only once. Multiple turns
will cause you to cut into the inner wires.
3.
Inspect the inner wires for damage.
If any wires are cut start over at step 1.
Check for damage
Specifications
Connection Tips and Troubleshooting
Problem:
Not linking with Bluetooth device or Linking with Bluetooth device, but no audio plays.
Troubleshooting:
1. Restart Bluetooth Dock
2. Restart Bluetooth Device
3. Make sure Bluetooth device is in play mode
Warning: Do not adjust the volume all the way up if no audio is present. Doing so could
damage your speakers if audio reconnects.
Problem:
Troubleshooting:
Verify you have connected the CAT5 cable correctly. Follow the TIA-568A
standard at both ends. Mis-wiring can cause distorted sound, prevent the system from
functioning, or possibly cause damage to the components in the system. Verify you have
connected the speakers in phase. Follow the label on the product. Out of phase speakers can rob
the system of its bass, especially when driving dual-voice-coil speakers.
If no audio is heard, check to make sure that the audio source is playing, then press the power
button on the keypad to make sure it is turned on.
Audio quality issues
Problem:
Hum in System
Troubleshooting:
Plug all parts of the system into the same outlet to see if the hum goes away.
Try lifting the ground with a ground lifting plug.
Possible Cause:
The different components in the system are connected to different electrical
grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz
hum.
Solution:
Plug products into an electrical circuit with a common ground.
Problem:
iPod not charging (system not powering on)
Troubleshooting:
Bypass your wiring and use a pre-made CAT5 cable to your breakout plate.
Check the power supply with a volt meter. (Center positive) Using a small flathead screwdriver,
carefully spread the center pin inside the female power connector on the breakout plate.
Possible Cause:
The different components in the system are connected to different electrical
grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz
Additional Tips:
1. The A0320 is designed to provide 5vDC of charging voltage. The device screen should
indicate that ir is being charged. If this does not occur, make sure the power is reaching the
volume control keypad (press the volume buttons to see if the LED indicators light up).
2. Observe wiring distance specifications. The maximum recommended wire length
between the wall dock and the breakout plate is 350 feet. Although the A0320 may work at
greater distances, extreme distances are not recommended because erratic performance
may result due to the power loss caused by the CAT5 wire.
3. If you are experiencing problems with your device that occur even when it is not docked in
the A0320, then please contact customer service of that manufacturer for support.
NOTE: Maximum charging voltage is 5vDC 500mA. Do not plug in a device such as
a tablet computer to this dock. Doing so can cause damage to either device and will
void the warranty.
