background image

II. Safety 

     WARNING:

 THIS MACHINE CAN CAUSE SERIOUS INJURY OR DEATH!!!! 

THOROUGHLY READ INSTRUCTIONS BEFORE INSTALLING OR OPERATING TRAP!  

DO NOT STAND IN FRONT OF THE TRAP WHEN IT IS IN THE COCKED POSITION. 
SERIOUS INJURY OR DEATH CAN RESULT. 

THIS TRAP IS CAPABLE OF THROWING TARGETS A DISTANCE OF OVER 65 YARDS.  
USE ONLY IN AREAS WHERE THERE IS NO RISK OF CAUSING DAMAGE, OR HITTING 
A PERSON WITH A TARGET. 

KNOW YOUR BACKSTOP.  ENSURE THERE IS A SAFE PERIMETER THROUGHOUT 
TARGET FLIGHT PATH SUFFICIENT FOR AMMUNITION USED. 

      

WARNING:

 IF THERE IS A TARGET ON THE THROWING ARM, SAFE RELEASING 

THE ARM WILL THROW THE TARGET. DO NOT STAND IN FRONT OF THE TRAP WHILE 
SAFE RELEASING THE THROWING ARM. 

CAUTION: THE TRAP MUST HAVE AMPLE CLEARANCE AROUND THE TRAP.  THE 
ON/OFF/SAFE RELEASE SWITCH FOR THE TRAP IS LOCATED ON THE REAR OF THE 
TRAP AND ALLOWS THE TRAP TO BE UNCOCKED BEFORE APPROACHING IT.   

DO NOT INSTALL THE TRAP IN AN AREA THAT DOES NOT ALLOW SAFE (REAR) 
ACCESS TO THE TRAP AND THE ON/OFF/SAFE RELEASE SWITCH DURING LOADING 
AND USE.  

 

1.  All  personnel  operating  the  trap  should  be  thoroughly  familiar  with  the 

operating instructions and the safety issues relating to the trap. 

2.  Do not leave trap in the cocked position. Not only is this potentially dangerous, 

but it puts undue stress on the mainspring. 

3.  Always load and operate the trap from the rear (switch end). 

4.  Keep hands and body outside the trap and throwing arm path indicator areas 

while  the  trap  is  operating.  This  ring  shows  the  throwing  arm‟s  path  when 
throwing a target, and should always be attached to the trap when it is in use. 

5.  Be aware that a cracked or broken target thrown from the trap will sometimes 

scatter  pieces  out  the  right  side  of  the  machine  as  the  arm  throws.  These 
pieces may hit nearby unsuspecting bystanders. 

6.  Always wear eye and hearing protection when shooting. 

 

 

 

Содержание WHEELYBIRD 40909























Отзывы: