Champion Eseries HRU Скачать руководство пользователя страница 7

Страница: 7 / 42

Installation

Installation

Receiving

NOTE:

The installation of your Heat Recovery Unit

(HRU)

must be performed by qualified service

personnel. Problems due to improper installation are not covered by the Warranty.

The HRU may have be installed at the factory. Proceed to the operation section of this manual
if your HRU is already attached to the machine.

Inspect the HRU for damage due to shipping.

Check for any accessories that may have shipped with your dishwasher.

Move the HRU near its permanent location.

CAUTION:

Be careful when lifting and moving the HRU to prevent damage to the machine.

NOTE:

The installation of the HRU must comply with local safety and health codes.

Compare the installation site utility connections with the dishwasher utility connections and
make sure that they are the same.

For new dishwasher installations, install the Dishwasher according to the instructions in the
dishwasher service manual

Installation, Operation, and Service Replacement Parts

, which

is shipped inside the dishwasher.

WARNING:

Electrocution or serious injury may result when working on an
energized circuit.

Disconnect power at the main breaker or service disconnect
switch before working on the circuit.

Lock-out and tag the breaker to indicate that work is being
performed on the circuit.

WARNING:

Moving Parts may cause INJURY OR DEATH.

USE EXTREME CAUTION WHEN THE CONVEYOR

IS MOVING.

Содержание Eseries HRU











































Результаты поиска

Содержание Eseries HRU

Отзывы:

Бренды по названию

Популярные бренды

Champion Eseries HRU, Руководство по установке и эксплуатации с перечнем запасных частей для сервисного обслуживания

Результаты поиска

Содержание Eseries HRU

Отзывы:

Бренды по названию

Популярные бренды