background image

 

NORRISEAL-WELLMARK 

REVISION 2021-5-14 

 

Norriseal-Wellmark 

11122 WEST LITTLE YORK RD 
HOUSTON, TX 77041 
NORRISEALWELLMARK.COM 
(713) 466-3552 

 

DigiUltra Pump Controller

 

 

Timberline and Wellmark 

Solar/Electric Chemical Injection Pumps

 

QUICK START GUIDE 

 COMMUNICATIONS

 

Contents

 

Overview ............................................................................ 1 

Comm Specifications .......................................................... 1 

Faceplate Reference ........................................................... 1 

Configuring Communication Settings ................................. 2 

Enabling Communication ............................................... 2 

Adjusting Serial Port Settings ......................................... 3 

Serial Connections .............................................................. 4 

Connecting to Serial Radios ............................................ 4 

Critical Radio Network Settings ...................................... 4 

Converting to RS232 Communication ............................ 4 

Modbus TCP/IP Connections .............................................. 5 

Tiny Gateway Connections ............................................. 5 

Critical Device Settings ................................................... 5 

 

Overview 

This  document  will  assist  with  configuring  the  serial  communications  on  the 
DigiUltra pump controller. 

Comm Specifications 

Protocol 

Modbus RTU 

Connections 

2-Wire RS485 

Allowable Addresses 

1-247 

     Default Address 

16 

Baud Rate (Selectable) 

4800 

9600 (Default) 

19,200 
38,400 
57,600 

Data Bits 

Parity 

None 

Stop Bits 

Faceplate Reference 

 

Содержание DigiUltra











Отзывы: