NORRISEAL-WELLMARK
9
REVISION 2021-5-14
Holding Registers
TYPE
ADDRESS DESCRIPTION
VALUE MEANING
ADDITIONAL NOTES
HOLD REG
40005
Total Cycle Time
0: 30 seconds
1: 60 seconds
2: 300 seconds (5 minutes)
HOLD REG
40006
Motor Size
Motor Size in RPM
HOLD REG
40009/40010
Timer On Time
On Time in Seconds (32 bit value)
9: lower word (16 bits)
10: upper word (16 bits)
HOLD REG
40011/40012
Timer Off Time
Off Time in Seconds (32 bit value)
11: lower word (16 bits)
12: upper word (16 bits)
HOLD REG
40013
Temperature Set point
Switched Set point or
Scaled Upper Temperature
deg F
HOLD REG
40014
Temperature Set point
Scaled Lower Temperature
deg F
HOLD REG
40015/40016
Minimum QPD
QPD at Upper Temperature
float value
15: lower 16 bits
16: upper 16 bits
HOLD REG
40017/40018
Maximum QPD
QPD at Lower Temperature
float value
17: lower 16 bits
18: upper 16 bits
HOLD REG
40019/40020
QPD
Set Quarts/Day Value
float value
19: lower 16 bits
20: upper 16 bits
HOLD REG
40022/40023
Auxillary Timer On Time
On time in seconds (32 bit value)
22: lower word (16 bits)
23: upper word (16 bits)
HOLD REG
40024/40025
Auxillary Timer Off Time
Off time in seconds (32 bit value)
24: lower word (16 bits)
25: upper word (16 bits)
HOLD REG
40027/40028
Batch Delay / Batch Start
In seconds (32 bit value)
If Batch type = delay; this is the amount of delay (0-120 hours)
If Batch type=scheduled; this is the start time (0-23 hours)
27: lower word (16 bits)
28: upper word (16 bits)
HOLD REG
40029/40030
Batch Run Time
On time in seconds (32 bit value)
29: lower word (16 bits)
30: upper word (16 bits)
HOLD REG
40031/40032
Batch Amount
Auto mode batch volume in QPD
float value
31: lower 16 bits
32: upper 16 bits
HOLD REG
40033
Display Turn off
Time in seconds until display turns off
HOLD REG
40034
Cal Rate Pulses
Number of pulses counted in Cal Rate
0-999
HOLD REG
40035
Cal Rate Ticks
Number of ticks dropped in Cal Rate
Where ticks = 1Quart per Day per 1 Minute Test interval
(Standard rate gauge increment for Kenco 929 or similar)
HOLD REG
40036
Tank #1 Low Value
Low Scale, minimum value (Value=Inches*10)
5-1150; inches value input by user x 10
HOLD REG
40037
Tank #1 High Value
High Scale, maximum value (Value=Inches*10)
5-1150; inches value input by user x 10
HOLD REG
40038
Tank #2 Low Value
Low Scale, minimum value (Value=Inches*10)
5-1150; inches value input by user x 10
HOLD REG
40039
Tank #2 High Value
High Scale, maximum value (Value=Inches*10)
5-1150; inches value input by user x 10
HOLD REG
40040
Tank #1 Low Calibration
12-bit ADC offset value
0-4095; Raw analog reading
HOLD REG
40041
Tank #1 High Calibration
12-bit ADC offset value
0-4095; Raw analog reading
HOLD REG
40042
Tank #2 Low Calibration
12-bit ADC offset value
0-4095; Raw analog reading
HOLD REG
40043
Tank #2 High Calibration
12-bit ADC offset value
0-4095; Raw analog reading
HOLD REG
40044
Tank #1 Low Alarm
Alarm Trip point, Tank 1
(Value=Inches*10)
0.5-115.0
HOLD REG
40045
Analog #1 Select
0: disabled
1: Inches
2: Raw
HOLD REG
40046
Tank #2 Low Alarm
Alarm Trip point, Tank 2
(Value=Inches*10)
0.5-115.0
HOLD REG
40047
Analog #2 Select
0: disabled
1: Inches
2: Raw
HOLD REG
40048
Cal method set
0: measured
1: calibrated
2: calculated
Lower byte used only
Calibration method selected by user
10MAY21
CODE VERSION
CHANGE NOTES
