Champion 91050 Скачать руководство пользователя страница 30

Страница: 30 / 34

REV 91050-20140620

ENGLISH

91050

TROUBLESHOOTING

For further technical support:

Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[email protected]

Problem

Cause

Solution

Engine will not start

No fuel

Add fuel

Faulty spark plug

Replace spark plug

Unit loaded during startup

Remove load from unit

Engine starts but runs roughly

Low oil level

Fill crankcase to the proper level
Place chipper-shredder on a flat, level
surface

Choke in the wrong position

Adjust choke

Throttle in wrong position

Adjust throttle

Spark plug wire loose

Attach wire to spark plug

Engine shuts down during operation

Out of fuel

Fill fuel tank

Low oil level

Fill crankcase to the proper level
Place chipper-shredder on a flat, level
surface

Engine cannot supply enough power or
overheating

Insufficient ventilation

Check for air restriction. Move to a
well ventilated area

No materials are discharged

Flail housing clogged

Stop engine immediately, disconnect
spark plug, take apart flail housing to
clear clog

Deflector chute clogged

Stop engine immediately, disconnect
spark plug, take apart deflector chute
to clear clog

Collection bag is full

Stop engine, disconnect spark plug,
empty collection bag

Discharge rate slows or discharge
material changes

Low engine power

Increase throttle

Chipper blades, shredder blade and
flail blades are dull

Stop engine, disconnect spark plug,
take apart flail housing and check all
blades. Sharpen if needed

Excessive vibration or unusual noise
while engine is running or material is
being processed

Engine power to high

Decrease throttle

Foreign object(s) in chutes or flail
housing

Stop engine immediately, disconnect
spark plug, inspect all chutes and
take apart flail housing to inspect for
foreign object (s)

Impeller overloaded with material

Allow impeller to run current material
load through before adding more

Material is too dry or thick for blades

Remove material immediately

Содержание 91050



































Результаты поиска

Содержание 91050

Отзывы:

Похожие инструкции для 91050

Бренды по названию

Популярные бренды

Champion 91050, Руководство пользователя и инструкции по эксплуатации

Результаты поиска

Содержание 91050

Отзывы:

Похожие инструкции для 91050

Бренды по названию

Популярные бренды