background image

EMISSION CONTROL SYSTEM WARRANTY

The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage

1.  APPLICABILITY:

 This warranty shall apply to 1997 and later model year small off-road engines (SORE). The ECS Warranty Period shall 

begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive 
months thereafter.

2.  GENERAL EMISSIONS WARRANTY COVERAGE

 

CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent purchaser that each of its 
small off-road engines (SORE) is:

2a. Designed, built and equipped so as to conform to U.S. EPA emissions standards for spark-ignited engines at or below 19 kilowatts.

2b. Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects 

to the part as described in the engine manufacturer’s application for certification for a period of two years.

3.  THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS FOLLOWS:

3a. Any warranted part that is not scheduled for replacement as required maintenance in the Owners Manual shall be warranted for 

the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or replaced by CPE according 
to Subsection “d” below. Any such part repaired or replaced under the ECS Warranty shall be warranted for any remainder of the 
ECS Warranty Period.

3b. Any warranted, emissions-related part which is scheduled only for regular inspection as specified in the Owners Manual shall be 

warranted for the ECS Warranty Period. A statement in such written instructions to the effect of “repair or replace as necessary”, 
shall not reduce the ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the 
remainder of the ECS Warranty Period.

3c. Any warranted, emissions-related part which is scheduled for replacement as required maintenance in the Owner’s Manual shall 

be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first 
scheduled replacement, the part shall be repaired or replaced by CPE according to Subsection “d” below. Any such emissions-
related part repaired or replaced under the ECS Warranty, shall be warranted for the remainder of the ECS Warranty Period prior to 
the first scheduled replacement point for such emissions-related part.

3d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be performed at no charge to the 

owner at a CPE Authorized Service Outlet.

3e. The owner shall not be charged for diagnostic labor which leads to the determination that a part covered by the ECS Warranty is in 

fact defective, provided that such diagnostic work is performed at a CPE Authorized Service Outlet.

3f.  CPE shall pay for covered emissions warranty repairs at non-authorized service outlets under the following circumstances:

i. The service is required in a population center with a population over 100,000 according to U.S. Census 2000 without a CPE 

Authorized Service Outlet AND

ii. The service is required more than 100 miles from a CPE Authorized Service Outlet. The 100 mile limitation does not apply in the 

following states: Alaska, Arizona, Colorado, Hawaii, Idaho, Montana, Nebraska, Nevada, New Mexico, Oregon, Texas, Utah and 
Wyoming.

3g. CPE shall be liable for damages to other original engine components or approved modifications proximately caused by a failure 

under warranty of an emission-related part covered by the ECS Warranty.

3h. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emission-related parts sufficient to meet the 

expected demand for such emission-related parts.

3i.  Any CPE Authorized and approved emission-related replacement part may be used in the performance of any ECS Warranty 

maintenance or repair and will be provided without charge to the owner. Such use shall not reduce CPE’s warranty obligation.

3j.  Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such use voids this ECS Warranty and 

shall be sufficient grounds for disallowing an ECS Warranty claim. CPE shall not be liable hereunder for failures of any warranted 
parts of a CPE engine caused by the use of such an unapproved add-on or modified part. 

Содержание 100458

































Отзывы: