manualshive.com logo in svg

Champion 100387, Руководство оператора

Поделиться
Скачать
Champion 100387 Скачать руководство пользователя страница 18

15

ENGLISH

 

100387

MAINTENANCE AND STORAGE

The owner/operator is responsible for all periodic 
maintenance.

Complete all scheduled maintenance in a timely manner. 
Correct any issue before operating the generator.

Air filter

1.  Remove the maintenance cover.
2.  Locate the air filter plastic cover. 
3.  Unsnap the locking hinge on the cover.
4.  Remove the old filter. 
5.  Place the new filter in the assembly.
6.  Re-snap the hinge on the air filter cover.
7.  Reinstall the maintenance cover and tighten the 

cover screw securely.

Spark Plugs

1.  Remove the maintenance cover.
2.  Remove the spark plug cable from the spark plug
3.  Use a spark socket (not included) to remove the plug.
4.  Remove the spark plug.
5.  Inspect the electrode on the plug. It must be clean 

and not worn to produce the spark required for 
ignition.

6.  Make certain the spark plug gap is 0.7 - 0.8 mm 

(0.028 - 0.031 in.).

7.  Carefully thread the plug into the engine.
8.  Use a spark plug socket (not included) to firmly 

install the plug.

9.  Attach the spark plug cap to the plug.
10. Reinstall the spark plug access cap, and 

maintenance cover.

For service or parts assistance, contact our help 
line at 

1-877-338-0999

NOTE

Maintenance, replacement, or repair of emission 
control devices and systems may be performed 
by any non-road engine repair establishment or 
individual.

NOTE

Never operate a damaged or defective generator.

WARNING

Tampering with the factory set governor will void 
your warranty.

WARNING

Improper maintenance will void your warranty.

WARNING

Oil Cont’d.

0.7 - 0.8 mm

0.028 - 0.031 in.

Once oil has been added, a visual check should show 
oil about 1-2 threads from running out of the fill hole.
If using the dipstick to check oil level, DO NOT screw 
in the dipstick while checking.

NOTE

Engine Maintenance

To prevent accidental starting, remove and ground spark 
plug wire before performing any service.

Oil 

Change oil when the engine is warm. Refer to the oil 
specification to select the proper grade of oil for your 
operating environment.
1.  Set the generator on top of a work bench or table.
2.  Loosen the cover screws and remove the 

maintenance cover.

3.  Pop up the rubber maintenance plug, from below the 

drain bolt.

4.  Remove the drain bolt.
5.  Allow the oil to drain completely.
6.  Replace the drain plug.
7.  Add up to 0.6 L (0.6 qt.) of oil and replace oil fill 

cap/dipstick. DO NOT OVERFILL.

8.  Reinstall the maintenance cover and tighten the 

cover screws.

9.  Dispose of used oil at an approved waste 

management facility.

Содержание 100387
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды