Champion 100387 Скачать руководство пользователя страница 13

10

100387

 

ENGLISH

ASSEMBLy

Add Engine Oil Cont’d.

Synthetic oil may be used after the 5 hour initial 
break-in period. Using synthetic oil does not 
increase the recommended oil change interval. 
Full synthetic 5W-30 oil will aid in starting in cold 
ambient <5ºC (41ºF)

NOTE

Weather will affect engine oil and engine 
performance. Change the type of engine oil used 
based on weather conditions to suit the engine 
needs.

NOTE

Add fuel

1.  Use clean, fresh, regular unleaded fuel with a 

minimum octane rating of 85 and an ethanol content 
of less than 10% by volume.

2.  DO NOT mix oil with fuel.
3.  Clean the area around the fuel cap. 
4.  Remove the fuel cap.
5.  Slowly add fuel to the tank. DO NOT OVERFILL. Fuel 

can expand after filling. A minimum of 6.4 mm (¼ in.) 
of space left in the tank is required for fuel expansion, 
more than 6.4 mm (¼ in.) is recommended. Fuel 
can be forced out of the tank as a result of expansion 
if it is overfilled, and can affect the stable running 
condition of the product. When filling the tank, it is 
recommended to leave enough space for the fuel to 
expand.

6.  Screw on the fuel cap and wipe away any spilled fuel.

Use regular unleaded gasoline with a minimum 
octane rating of 85.

Do not mix oil and gasoline.
Fill tank to approximately 6.4 mm (¼ in.) below the 
top of the tank to allow for fuel expansion.
DO NOT pump gas directly into the generator at the 
gas station. Use an approved container to transfer 
the fuel to the generator.
DO NOT fill fuel tank indoors.
DO NOT fill fuel tank when the engine is running or hot.
DO NOT overfill the fuel tank.
DO NOT light cigarettes or smoke when filling the 
fuel tank.

CAUTION

Pouring fuel too fast through the fuel screen may 
result in blow back of fuel at the operator while filling.

WARNING

Add fuel Cont’d.

Our engines work well with 10% or less ethanol 
blend fuels. When using blended fuels there are 
some issues worth noting: 

 

– Ethanol-gasoline blends can absorb more water 

than gasoline alone. 

 

– These blends can eventually separate, leaving 

water or a watery goo in the tank, fuel valve and 
carburetor. 

 

– With gravity-fed fuel supplies, this compromised 

fuel can be drawn into the carburetor and cause 
damage to the engine and/or potential hazards. 

 

– There are only a few suppliers of fuel stabilizer 

that are formulated to work with ethanol blend 
fuels.

 

– Any damages or hazards caused by using 

improper fuel, improperly stored fuel, and/
or improperly formulated stabilizers, are not 
covered by manufacture’s warranty. 

It is advisable to always shut off the fuel supply, 
run the engine to fuel starvation and drain the tank 
when the equipment is not in use for more than 30 
days.

NOTE

Grounding

Your generator must be properly connected to an 
appropriate ground to help prevent electric shock.

A ground terminal connected to the frame of the generator 
has been provided on the power panel. For remote 
grounding, connect a length of heavy gauge (12 AWG 
minimum) copper wire between the generator ground 
terminal and a copper rod driven into the ground. We 
strongly recommend that you consult with a qualified 
electrician to ensure compliance with local electrical codes.

Failure to properly ground the generator can result 
in electric shock.

WARNING

Содержание 100387
































Отзывы: