background image

100386 - 4200 PSI PRESSURE WAShER

SAfETY SYMbOLS

4

SAfETY SYMbOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of 
these symbols will allow you to more safely operate the product.

SYMBOL

MEANING

Read the Operator’s Manual.

 To reduce the risk of injury, user must read and understand operator’s 

manual before using this product.

Electric Shock.

 Failure to use in dry conditions and to observe safe practices can result in electric shock.

Toxic Fumes.

 The engine exhaust from this product contains chemicals known to the state of California to 

cause cancer and birth defects and other reproductive harm.

Risk of Asphyxiation.

 This engine emits carbon monoxide, an oderless, colorless poison gas. Breathing 

carbon monoxide can cause nausea, fainting or death. Use only in a well ventilated area.

Risk of Injections.

 To reduce the risk of injection or injury, never direct a water stream towards people or 

pets or place any body part in the stream. Leaking hoses and fittings are also capable of causing injection 
injury. Do not hold hoses or fittings.

Eye and Ear Protection.

 Always wear safety goggles or safety glasses with side shields, and as necessary 

a full faceshield as well as full ear protection when operating this product.

Kickback.

 To reduce the risk of injury from kickback, hold the trigger gun securely with both hands when 

the machine is on.

Risk of Fire.

 Fuel and its vapors are extremely flammable and explosive. Fire can cause severe burns or 

death. Do not add fuel while the product is operating or still hot. Do not spray flammable liquids. Operate 
only where open flame is permitted.

Risk of Explosion.

 Do not spray flammable liquids. Flammable liquids, fuel, and their vapors are explosive 

and can cause severe burns or death.

Содержание 100386



































Отзывы: