Model 100199
INSTALLATION
40
Part No. 101049 Rev. B
16. Pin 16 Gen AC Detect
R (Red)
DIP SWITCHES
on the backside of the control, between the 2
rows of pin connectors
The Dip Switches set parameters of the controller for delay
sequences. There are only 10 dip switches. These are the
designated “ON” or “OFF” position settings for the dip switches;
1. Position 1 is in the “ON” position
2. Position 2 is in the “ON” position
3. Positions 3 – 9 are in the “OFF” position
4. Position 10 is in the “ON” position
These are factory set delays or activation signals.
BATTERY CHARGER
This automatic battery charger is an intelligent module which
maintains lead acid batteries at a full charge, when the HSB has
been properly installed. Continual monitoring and maintenance
will promote long battery life. In accordance with the principle of
high ef
fi
ciency, at Full Load, >85% of ef
fi
ciency is achieved. This
charger is a maintenance battery charger. If the battery voltage
falls below 6V, the charger will not re-change the batteries.
To properly maintain battery ef
fi
ciency you must follow the
battery manufacturers; safety instructions, warnings and proper
maintenance procedures.
Feature bene
fi
ts include; reverse polarity protection, short
circuit protection, overload protection, over voltage, over current,
fl
oating charging system, constant voltage output and a rugged
design for industrial environments. The charger is also equipped
with a manual reset which is located on the far right side of the
wire land points. This charger is for lead acid batteries only. All
adjustments are preset at the factory.
The automatic battery charger has
fi
ve (5) built in LEDs that
display the following, view left to right;
NO CHARGE / PAS DE CHARGE /
SIN CARGA
AUTOMATIC BATTERY CHARGER /
CHARGE AUTOMATIQUE DE BATTERIE /
CARGADOR DE BATERÍA AUTOMÁTICO
Output: 24 Vdc 1.6 A
Producción: 24 V C.C. 1,6 A
Sortie : 24 V c.c. 1,6 A
Power: 80-125 Vac 1.0 A 50 / 60 Hz
Potencia: 80 - 125 V C.A. 1,0 A 50 / 60 Hz
Alimentation : 80-125 V c.a. 1,0 A 50 / 60 Hz
L
N
ADJ
E. O.
V
POWER / ALIMENTATION /
POTENCIA
OUTPUT / SORTIE /
PRODUCCIÓN
MODEL / MODÈLE / MODELO : 100482
POWER
ALIMENTATION
POTENCIA
Conforms to UL
Std. 1236
RECOGNIZED
COMPONENT
Black
PMS 109 C
PMS 485 C
PMS Reflex Blue C
1. Power – Lit to indicate the battery is fully charged.
2. Small Bar – Lit to indicate the battery is receiving a trickle
charge.
3. Middle Bar – Lit to indicate current output is near 50%.
4. Large Bar – Lit to indicate the charger is operating above
50% capacity.
5. NO CHARGE – Lit to indicate a battery charging problem.
If this LED is lit, the LED on the Engine Controller module,
“LOW BATTERY” will also be lit.
The battery(s) might be discharged to a level that is too low to re-
charged with this charger (battery voltage below 6V). If this is the
case, the batteries will need to be charged individually. Remove
all battery cables from the batteries and follow the battery
manufacturers’ instructions on properly servicing/charging the
batteries.
Be careful to avoid corrosion on the battery post(s). Corrosion
can have the effect of creating an insulation between the post(s)
and the cable(s), this will severely affect the performance of the
battery. Follow battery manufacturers’ instructions on proper
maintenance, service or replacement. The correct wire lands are
read left to right, 6 land points;
