background image

2

TABLE OF CONTENTS

When you see these Safety Symbols and Signal
Words on the following pages, they will alert you to
the possibility of 

serious injury or death

if you do

not comply with the warnings that accompany them.
The hazard may come from something mechanical
or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following
pages, it will alert you to the possibility of damage to
your garage door and/or the garage door opener if
you do not comply with the cautionary statements
that accompany it. Read them carefully.

INTRODUCTION

Safety Symbol 
and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the instructions and warnings contained in this manual.

Mechanical

Electrical

WARNING

CAUTION

WARNING

WARNING

WARNING

CAUTION

WARNING

WARNING

WARNING

CAUTION

WARNING

WARNING

Introduction

2-7

Safety symbol and signal word review........................2

Preparing your garage door ........................................3

Tools needed ...............................................................3

Planning ..................................................................4-5

Carton inventory ..........................................................6

Hardware inventory .....................................................7

Assembly 8-11

Assemble the rail and install the trolley ......................8

Fasten the rail to the motor unit and
Install the idler pulley...................................................9

Install the belt and attach the belt cap retainer.........10

Set the tension ..........................................................11

Installation 11-26

Installation safety instructions....................................11

Determine the header bracket location .....................12

Install the header bracket..........................................13

Attach the rail to the header bracket.........................14

Position the opener ...................................................15

Hang the opener .......................................................16

Install the door control...............................................17

Install the lights .........................................................18

Attach the emergency release rope and handle .......18

Electrical requirements..............................................19

Install The Protector System

®

..............................20-22

Fasten the door bracket .......................................23-24

Connect the door arm to the trolley .....................25-26

Adjustment

27-29

Adjust the travel limits ...............................................27

Adjust the force .........................................................28

Test the safety reversal system.................................29

Test The Protector System

®

......................................29

Operation  

30-34

Operation safety instructions.....................................30

Using your garage door opener ................................30

Using the wall-mounted door control ........................31

To open the door manually........................................31

Care of your garage door opener..............................32

Having a problem? ....................................................33

Diagnostic chart.........................................................34

Programming

35-36

To add or reprogram a hand-held remote control .....35

To erase all codes .....................................................35

3-Button remotes.......................................................35

To add, reprogram or change 
a Keyless Entry PIN ..................................................36

Repair Parts  

37-38

Rail assembly parts ...................................................37

Installation parts ........................................................37

Motor unit assembly parts .........................................38

Accessories

39

Repair Parts and Service

40

Warranty

40

Содержание Whisper Drive Security+ WD822KLS









































Отзывы: