background image

22

Carriage Bolt 
1/4"-20x1/2"

Lens

Wing Nut
1/4"-20

Figure 5

MOUNTING AND WIRING THE SAFETY 
REVERSING SENSORS

•  

Slide a 1/4"-20x1/2" carriage bolt head into the slot 
on each sensor. Use wing nuts to fasten sensors to 
brackets, with lenses pointing toward each other 
across the door. Be sure the lens is not obstructed 
by a bracket extension (Figure 5).

•  

Finger tighten the wing nuts. 

•  

Run the wires from both sensors to the opener. Use 
insulated staples to secure wire to wall and ceiling. 

•  

Strip 7/16" (11 mm) of insulation from each set of 
wires. Separate white and white/black wires 
sufficiently to connect to the opener quick-connect 
terminals. Twist like colored wires together. Insert 
wires into quick-connect holes: white to white and 
white/black to grey (Figure 6).

ALIGNING THE SAFETY REVERSING SENSORS

•  

Plug in the opener. The indicator lights in both the 

sending

 and 

receiving eyes

 will 

glow

 

steadily

 if 

wiring connections and alignment are correct.

The 

sending 

eye amber indicator light will glow 

regardless of alignment or obstruction. If the green 
indicator light in the 

receiving eye

 is

 

off, dim, or 

flickering (and the invisible light beam path is not

 

obstructed), alignment is required.

•  

Loosen the 

sending

 

eye

 wing nut and readjust, 

aiming directly at the 

receiving

 

eye.

 Lock in place.

•  

Loosen the 

receiving

 

eye

 wing nut and adjust 

sensor until it receives the sender’s beam. When 
the green indicator light 

glows steadily

, tighten the 

wing nut.

TROUBLESHOOTING THE  SAFETY 
REVERSING SENSORS

1.  If the 

sending eye

 indicator light does not 

glow 

steadily

 after installation, check for:

 • 

 

Electric power to the opener.

 • 

 

A short in the white or white/black wires. These 
can occur at staples, or at opener connections.

 • 

 

Incorrect wiring between sensors and opener.

 • 

 

A broken wire.

2.  If the 

sending

 

eye

 indicator light 

glows steadily

 but 

the 

receiving

 

eye

 indicator light doesn't:

 • 

 

Check alignment.

 • 

 

Check for an open wire to the 

receiving

 

eye

.

3.  If the 

receiving

 

eye

 indicator light is dim, realign 

either sensor.

NOTE: 

When the invisible beam path is obstructed or 

misaligned while the door is closing, the door will 
reverse. If the door is already open, it will not close. 
The opener lights will blink 10 times. See page 20.

 

Invisible Light Beam 
Protection Area 

Safety Reversing Sensor 

Safety Reversing  
Sensor 

Connect Wire to 
Quick-Connect Terminals 

Bell Wire 

Bell Wire 

Finished 
Ceiling 

Quick-Connect Terminals

3.  To insert or release 
     wire, push in tab with
     screwdriver tip

1.  Strip wire 7/16" 
     (11 mm) 

2.  Twist like colored  
     wires together 
 

7/16" (11 mm) 

Red

Grey

White

Figure 6

Содержание Security+ PD300DM









































Отзывы: