Chamberlain Security+ 8200 Series Скачать руководство пользователя страница 5

Страница: 5 / 40

Access
Door

Safety
Reversing Sensor

Safety
Reversing
Sensor

CLOSED POSITION

Header
Bracket

Belt
Pulley Bracket

Door
Bracket

Straight
Door
Arm

Curved
Door Arm

Trolley

Emergency Release
Rope & Handle

T-rail

Garage
Door

Belt

Header
Wall

Gap between floor
and bottom of door
must not exceed 1/4".

Planning (Continued)

ONE-PIECE DOOR INSTALLATIONS

• Generally, a one-piece door does not require

reinforcement. If your door is lightweight, refer to
the information relating to sectional doors in
Installation Step 11.

• Depending on your door’s construction, you may

need additional mounting hardware for the door
bracket (Step 11).

FINISHED CEILING
Support bracket
& fastening
hardware is required.
See page 17.

Safety
Reversing
Sensor

Safety Reversing
Sensor

Header
Wall

Access Door

Gap between floor
and bottom of door
must not exceed 1/4".

ONE-PIECE DOOR WITHOUT TRACK

CLOSED POSITION

Belt
Pulley Bracket

Header
Bracket

Trolley

Straight
Door
Arm

Emergency
Release
Rope & Handle

Door
Bracket

Curved
Door
Arm

Header
Wall

Belt

T-rail

Garage
Door

ONE-PIECE DOOR WITH TRACK

Without a properly working safety reversal system,
persons (particularly small children) could be
SERIOUSLY INJURED or KILLED by a closing garage
door.
• The gap between the bottom of the garage door and

the floor MUST NOT exceed 1/4". Otherwise, the safety
reversal system may not work properly.

• The floor or the garage door MUST be repaired to

eliminate the gap.

WARNING

CAUTION

WARNING

ATTENTION

AVERTISSEMENT

Содержание Security+ 8200 Series









































Результаты поиска

Содержание Security+ 8200 Series

Отзывы:

Похожие инструкции для Security+ 8200 Series

Бренды по названию

Популярные бренды

Chamberlain Security+ 8200 Series, Руководство пользователя

Результаты поиска

Содержание Security+ 8200 Series

Отзывы:

Похожие инструкции для Security+ 8200 Series

Бренды по названию

Популярные бренды