background image

12

INSTALLATION STEP 1

Determine the Header Bracket
Location

Installation procedures vary according to garage door
types. Follow the instructions which apply to your
door.

SECTIONAL DOOR
AND ONE-PIECE DOOR WITH TRACK

1. Close the door and mark the inside vertical

centerline of the garage door.

2. Extend the line onto the header wall above the

door.

You can fasten the header bracket within 4 feet
of the left or right of the door center only if a
torsion spring or center bearing plate is in the
way; or you can attach it to the ceiling (see
page 14) when clearance is minimal. (It may be
mounted on the wall upside down if necessary,
to gain approximately 1/2".)

If you need to install the header bracket on a 2x4
(on wall or ceiling), use lag screws (not provided)
to securely fasten the 2x4 to structural supports as
shown here and on page 13.

3. Open your door to the highest point of travel as

shown. Draw an intersecting horizontal line on the
header wall 2" above the high point. This height
will provide travel clearance for the top edge of the
door.

Proceed to Step 2, page 14.

One-piece

door with

horizontal

track 

To prevent possible SERIOUS INJURY or DEATH:
• Header bracket MUST be RIGIDLY fastened to

structural support on header wall or ceiling, otherwise
garage door might not reverse when required. DO NOT
install header bracket over drywall.

• Concrete anchors MUST be used if mounting header

bracket or 2x4 into masonry.

• NEVER try to loosen, move or adjust garage door,

springs, cables, pulleys, brackets, or their hardware, all
of which are under EXTREME tension. 

• ALWAYS call a trained door systems technician if

garage door binds, sticks, or is out of balance. An
unbalanced garage door might not reverse when
required.

Header Wall

Ceiling

Track

Highest Point
of Travel

Door

2"

Sectional door
with curved
track

Door

Track

Header Wall

Highest Point
of Travel

2"

Vertical
Centerline

Finished
Ceiling

Vertical
Centerline

Header
Wall

2x4

Structural
Supports

WARNING

CAUTION

WARNING

WARNING

ATTENTION

AVERTISSEMENT

AVERTISSEMENT

AVERTISSEMENT

Содержание Security+ 8200 Series









































Отзывы: