Chamberlain Power Drive 3132E FS2 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 80

background image

ALL ONE-PIECE DOORS

1. Assemble the door arm:

• Fasten the straight and curved door arm sections

together to the longest possible length (with a 2
or 3 hole overlap).

• With the door closed, connect the straight door

arm section to the door bracket with the
5/16"x1-1/4" clevis pin.

• Secure with a ring fastener.

2. Adjustment procedures:

On one-piece doors, before connecting the door
arm to the trolley, the travel limits must be
adjusted. Limit adjustment screws are located on
the left side panel as shown on page 29. Follow
adjustment procedures below.

• Open door adjustment: decrease UP travel

limit

– Turn the UP limit adjustment screw

counter-clockwise 4 turns.

– Press the Door Control push bar. The trolley

will travel to the fully open position.

– Manually raise the door to the open position

(parallel to the floor), and lift the door arm to
the trolley. The arm should touch the trolley just
in back of the door arm connector hole. Refer
to the fully open trolley/door arm positions in
the illustration. If the arm does not extend far
enough, adjust the limit further. One full turn
equals 5 cm of trolley travel.

• Closed door adjustment: decrease DOWN

travel limit

– Turn the DOWN limit adjustment screw

clockwise 4 complete turns.

28

Door Arm

Door Arm
Connector Hole

Closed
Door

Outer Trolley

Emergency Release Handle

Inner Trolley

Outer Trolley

Open Door

Door Arm

Correct Angle

Door with
Backward Slant (Incorrect)

Inner Trolley

– Press the Door Control push bar. The trolley

will travel to the fully closed position.

– Manually close the door and lift the door arm to

the trolley. The arm should touch the trolley just
ahead of the door arm connector hole. Refer to
the fully closed trolley/door arm positions in the
illustration. If the arm is behind the connector
hole, adjust the limit further. One full turn
equals 5 cm of trolley travel.

3. Connect the door arm to the trolley:

• Close the door and join the curved arm to the

connector hole in the trolley with the remaining
clevis pin. It may be necessary to lift the door
slightly to make the connection.

• Secure with a ring fastener.

• Run the opener through a complete travel cycle. If

the door has a slight "backward" slant in full open
position as shown in the illustration, decrease the
UP limit until the door is parallel to the floor.

NOTE:

When setting the up limit on the following

page, the door should not have a "backward" slant
when fully open as illustrated below. A slight
backward slant will cause unnecessary bucking
and/or jerking operation as the door is being opened
or closed from the fully open position.

Nuts
5/16"-18

Lock
Washers
5/16"

Ring
Fastener

Straight
Arm

Bolts
5/16"-18x7/8

Door
Bracket

Clevis Pin
5/16"x1-1/4"

Curved
Door Arm

«
...
26
27
28
29
30
...
»

Содержание Power Drive 3132E FS2

















































































Отзывы:

Нет отзывов

Похожие инструкции для Power Drive 3132E FS2

Бренд: GBD Страницы: 36

Бренд: Topens Страницы: 4

Бренд: Seip Страницы: 23

Бренд: FAAC Страницы: 32

Бренд: Genie Страницы: 32

Бренд: Nice Страницы: 68

Бренд: Nice Страницы: 128

GDO-2 SecuraLife

Бренд: Automatic Technology Страницы: 20

Бренд: FAAC Страницы: 13

AccessMaster Security+ M150

Бренд: Chamberlain Страницы: 36

Бренд: Roger Technology Страницы: 16

WING 302 Series

Бренд: Dea Страницы: 32

Бренд: Dea Страницы: 44

Бренд: G.S.M Activate Страницы: 7

Бренд: TOPP Страницы: 56

Бренд: Key Automation Страницы: 20

Бренд: TdA Страницы: 13

Бренд: ASI DOORS Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды