background image

15

This is an adjustable, second stop position suitable for

ventilation, pedestrian or pet access, programmed to the

Transmitter.

To Activate this feature:

1.Start with the door fully

CLOSED

(figure 1). Drive the opener

UP (figure 2) and stop at the position required for

PET

access.

2.Enter PET activation mode by pressing the

PROG

and

UP

buttons together for 3 seconds (figure 3). Release when the

Courtesy light flashes once.

3.Press the transmitter button that you have allocated for this

feature (figure 4). Do not use the button already allocated for

normal operation. The Courtesy light will flash once when the

code is accepted.

TEST:

Press the transmitter once, and door will close, press

again, and door will return to the preset position.

If the door is above the preset position, when the button

is pressed, it will fully close.

To Deactivate this feature:

1.Start with the door fully

CLOSED.

2.Enter PET deactivation mode by pressing the

PROG

and

UP

buttons together for 3 seconds (figure 3). The Courtesy light

will flash twice, indicating the deactivation has occurred.

NOTE: Erasing all transmitter codes, as in the Wireless

programming section, will also delete this feature.

PARTIAL OPENING FEATURE (PET)

Indicator LED

Indicator LED

Door Fully Closed

figure 1

figure 3

or

26

1

s

e

rv

ic

e

w

w

w

m

@

m

B

B

A

2

114A3361

For Service Call

Installation Date

3

132A2900

RISK OF ENTRAPMENT

Repeat Safety Reverse Test monthly. Door

must reverse on contact with a 40mm obstacle

placed on the floor. Make necessary adjustments.
AUTOMATIC DRIVE:

Keep away from the area of the door since it may

operate unexpectedly.
EMERGENCY RELEASE:

To release, pull down firmly on the red handle.

114A3361

For Service Call

Installation Date

l

l

25

INSTALL WARNING LABELS

Three warning labels are provided with this opener: attach as indicated in the fig 1 to a clean and suitable surface.

1. Risk of entrapment: (English version) - place close to a fixed Wall Control(1).

2. EMERGENCY Release/Service label: - place on the Manual Release cord (2).

3. WARNING Child Entrapment: (triangle label) - place on a low inside panel of the door (3).

figure 4

figure 1

Indicator LED

figure 2

Содержание Merlin MS105MYQ

























Отзывы: