background image

© 2006, The Chamberlain Group, Inc.

114A3093C

All Rights Reserved

Replacement Parts

3V2032 Lithium battery (2 required)  . . . . . . . . . . .10A20

Visor clip  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B137

FOR SERVICE DIAL OUR TOLL FREE NUMBER:  

US: 1-800-528-2817

CANADA: 1-800-654-4736

1. Begin by having both the 372LM and 372LMC and

Remote Control X available. 

2. Press and hold both buttons

on the 372LM and 372LMC
until the yellow indicator light,
visible on the bottom through
a small hole, begins to blink.
It will blink for 30 seconds;
during this time it is in the
learn or training mode, and
the buttons can be released.

3. While it is in learn mode, hold

Remote Control X, another
CGI fixed or billion-code
transmitter, back to back with
FCC labels touching as
illustrated.

4.

Press and hold the Remote

Control X push button 

as you

slowly slide the remotes
across each other until the
372LM and 372LMC indicator
light blinks very rapidly,
indicating it has learned the
code. (If Remote Control X is
also a 372LM and 372LMC,
you must press and hold its

right

push button.)

5. The right button is now

sending the same identical
coded signal as Remote
Control X. This code will
remain inside the 372LM and
372LMC until replaced with another new code by
repeating steps 1-4 above, or by resetting to Security

®

.

When Several Remotes operate one device:

To match the 372LM and 372LMC to another 315MHz
CGI manufactured remote’s code (Remote Control X):

FCC Label

Remote Control X

Yellow

Indicator

Light

Resetting the right push button
back to Security

®

as follows.

Push and hold both buttons while
observing the small yellow indicator light.
Hold both buttons for ten seconds until
the yellow indicator light stops blinking.
The remote has defaulted to one of six
randomly preprogrammed Security

®

settings.

The Remote Control Batteries

The lithium batteries should
produce power for up to 5 years.
To replace, pry open case with
visor clip or screwdriver, as
shown. Insert batteries 

positive

side up (+).

Dispose of old batteries properly.

Yellow

Indicator

Light

To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

WARNING

CAUTION

WARNING

WARNING

Содержание LiftMaster Security+ 372LM

Страница 1: ...n is trainable KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 1 2 1 Press and release the learn button on the motor unit The learn indicator light will glow steadily for 30 seconds 2 Within 30 seconds press and hold the button on the hand held remote that you wish to operate your garage door 3 Release the button when the motor unit light blink It has learned the code If light bulbs are not installed two clicks w...

Страница 2: ...ust press and hold its right push button 5 The right button is now sending the same identical coded signal as Remote Control X This code will remain inside the 372LM and 372LMC until replaced with another new code by repeating steps 1 4 above or by resetting to Security When Several Remotes operate one device To match the 372LM and 372LMC to another 315MHz CGI manufactured remote s code Remote Con...

Страница 3: ...tre porte de garage 3 Relâcher le bouton lorsque l éclairage du moteur clignote Il a appris le code Si les ampoules ne sont pas posées deux clics se feront entendre 2 3 1 KG KG Les instructions sont décrites et illustrées ci dessous Figure 1 Bouton Droit Multi Usage Pour inactiver toute télécommande non désirée effacer d abord tous les codes Enfoncer et tenir le bouton learn du moteur jusqu à ce q...

Страница 4: ...l autre jusqu à ce que le témoin lumineux du 372LM ou 372LMC clignote très rapidement ce qui signifie qu elle a appris le code Si la télécommande X est également un 372LM ou 372LMC enfoncer et retenir le bouton poussoir droit 5 Le bouton droit émet maintenant le même signal codé que celui de la télécommande X Le 372LM ou 372LMC conservera ce code jusqu à ce qu il soit remplacé par un nouveau code ...

Отзывы: