background image

8

CARE OF YOUR OPENER

When properly installed, your opener will provide high performance with a minimum of maintenance. The opener does not
require additional lubrication. Limit and Force Settings: These settings must be checked and properly set when the opener is
installed. Weather conditions may cause some minor changes in the door operation, requiring some re-adjustments,
particularly during the first year of operation. Refer to limit and force setting in, sections  11 & 12, pages 6 & 7. Follow the
instructions carefully and repeat the safety reverse test after any adjustment. 

Remote Control: Additional remotes can be purchased at any time. Refer to Accessories. Any new remotes must be
programmed into the opener. Remote Control Battery: The lithium batteries should produce power for up to 5 years. If
transmission range lessens, replace the battery .

Special Features

1.Motion Detecting Control Panel

Connect white/red wire to the red quick connect
terminal and the white wire to the white quick connect 
terminal.

2.The Protector System™ (Safety Beams)

Connect both white wires to the white quick connect 
terminal and both white/black wires to the grey quick 
connect terminal.

3.Flashing light connection. 

The flashing light can be installed anywhere.

4.Battery Backup

To access the battery backup connector, remove
the knockout to the right of the start button.

5.Timer to close function

Is enabled by turning the dial to the required time.
The Protector System (Safety Beams) must be 
installed before using this function.

LOCK

LIGHT

1

2

3

4

5

0

50

180 sec.

15

Accessories

1. Model 128LM 2-Function Wireless Wall Control 

2. Model 94334E 4-Fuction Remote Control

3. Model 94330E Single-Function Remote Control

4. Model 94333E 3-Function Remote Control

5. Model 94335 3-Function Mini Remote Control

6. Model 9747E Keyless Entry System

7. Model 98LM Motion Detecting Control Panel

8. Model 760E Outside Keylock

9. Model 1702E Outside Quick Release

10. Model 770E The Protector System™

11. Model FLA230 Flashing Light Kit

12. Model 475 Battery Backup System

LOCK

LIGHT

1

2

3

4

5

6

7

8

9

10

11

12

16

Содержание LiftMaster Professional RDO800 Series















Отзывы: