background image

20

Installation

STEP 10 Install the door control

To prevent possible SERIOUS INJURY or DEATH from electrocution:

l

Be sure power is NOT connected BEFORE installing door control.

l

Connect ONLY to 12 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

l

Install door control within sight of garage door, out of reach of children at a minimum height of 5
feet (1.5 m), and away from ALL moving parts of door.

l

NEVER permit children to operate or play with door control push buttons or remote control
transmitters.

l

Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no
obstructions to door travel.

l

ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path
of closing garage door.

INTRODUCTION

Compatible with MyQ

®

enabled accessories, see page 40. Your garage door opener is compatible with

up to 2 MyQ

®

door controls.

NOTE:

Older Chamberlain door controls and third party products are not

compatible.

Install the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children
cannot reach, and away from the moving parts of the door. For gang box installations it is not necessary
to drill holes or install the drywall anchors. Use the existing holes in the gang box.

NOTE:

Your product may look different than the illustrations.

HARDWARE

Screw
6ABx1" (2)

Drywall 
Anchors (2) 

Screw
6-32x1" (2)

1. Strip 7/16 inch (11 mm) of insulation from one end of the wire and separate the wires.
2. Connect one wire to each of the two screws on the back of the door control. The wires can be

connected to either screw. If your garage is pre-wired for the door control choose any two wires to
connect, note which wires are used so the correct wires are connected to the garage door
opener in a later step.

3. Mark the location of the bottom mounting hole and drill a 5/32 inch (4 mm) hole.
4. Install the bottom screw, allowing 1/8 inch (3 mm) to protrude from the wall.
5. Position the bottom hole of the door control over the screw and slide down into place.
6. Lift the push bar up and mark the top hole.
7. Remove the door control from the wall and drill a 5/32 inch (4 mm) hole for the top screw.
8. Position the bottom hole of the door control over the screw and slide down into place. Attach the

top screw.

7/16" (11 mm) 

Wall

DRYWALL

GANG BOX

6ABx1"

6-32x1"

Drywall Anchor

4-5 

6-32x1"

GANG BOX

DRYWALL

6ABx1"

Drywall Anchor

Содержание HD420EV













































Отзывы: