background image

16

Installation

STEP 8 Install the door bracket

Fiberglass, aluminum or lightweight steel garage doors

WILL REQUIRE

reinforcement BEFORE

installation of door bracket. Contact the garage door manufacturer or installing dealer for opener
reinforcement instructions or reinforcement kit. Failure to reinforce the top section as required
according to the door manufacturer may void the door warranty.

A horizontal and vertical reinforcement is needed for
lightweight garage doors (fiberglass, aluminum, steel,
doors with glass panel, etc.) (not provided). A horizontal
reinforcement brace should be long enough to be secured
to two or three vertical supports. A vertical reinforcement
brace should cover the height of the top panel. Contact the
garage door manufacturer or installing dealer for opener
reinforcement instructions or reinforcement kit.

NOTE:

Many door reinforcement kits provide for direct attachment of the clevis pin and door arm. In this

case you will not need the door bracket; proceed to the next step.

Self-Threading Screw
1/4"-14x5/8" 

HARDWARE

OPTION A

SECTIONAL DOORS

1. Center the door bracket on the previously marked vertical centerline used for the header bracket

installation. Note correct UP placement, as stamped inside the bracket.

2. Position the top edge of the bracket 2"-4" (5-10 cm) below the top edge of the door, OR directly

below any structural support across the top of the door.

3. Mark, drill holes and install as follows, depending on your door’s construction.

Metal or light weight doors using a vertical angle iron brace between the door panel support and
the door bracket:

l

Drill 3/16" fastening holes. Secure the door bracket using the two 1/4"-14x5/8" self threading
screws. (Figure 1)

l

Alternately, use two 5/16"-18x2" bolts, lock washers and nuts (not provided). (Figure 2)

Metal, insulated or light weight factory reinforced doors:

l

Drill 3/16" fastening holes. Secure the door bracket using the self-threading screws. (Figure 3)

Wood Doors:

l

Use top and bottom or side to side door bracket holes. Drill 5/16" holes through the door and
secure bracket with 5/16"-18x2" carriage bolts, lock washers and nuts (not provided). (Figure 4)

NOTE:

The 1/4"-14x5/8" self-threading screws are not intended for use on wood doors.

FIGURE 1

FIGURE 3

FIGURE 4

FIGURE 2

Vertical 
Reinforcement

Vertical Centerline 
of Garage Door 

UP

Door Bracket

Vertical Reinforcement

Vertical Centerline 
of Garage Door

Hardware
(not provided)

Door Bracket

UP

Vertical 
Centerline
of Garage 
Door 

UP

Vertical Centerline of 
Garage Door 

Hardware

(not provided)

UP

Inside Edge of Door or
Reinforcement Board 

Self-Threading Screw
1/4"-14x5/8"

Self-Threading 
Screw
1/4"-14x5/8"

Содержание HD420EV













































Отзывы: