manualshive.com logo in svg

Chamberlain GH, Руководство по установке

Получите бесплатное руководство по установке и эксплуатации для Palm GH. Просто загрузите его с нашего веб-сайта. Этот руководитель поможет вам настроить и использовать продукт по максимуму его возможностей. Узнайте все о Palm GH прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

 31 

PROGRAMMING

NOTE:

 

The following programming requires a LiftMaster 

Monitored Entrapment Protection (LMEP) device.

Your 315 MHz Security

✚

® 

or dip switch remote control can be 

programmed to operate as a 3-button wireless control station: 
the large button will open the door, the middle button will close 
the door, and the third button will stop the door’s movement. 
You may set up this feature as follows:

1.   To enter programming press and release the RADIO button on 

the logic board (the RADIO LED will light).

2.   To program the OPEN button to a remote control press and 

release the OPEN button on the logic board. The RADIO LED 
will flash and then stay on solid. Then press the corresponding 
button on the remote control. The RADIO LED on the logic 
board will flash, this confirms that the remote control has been 
programmed. (By programming the remote you use 1 channel 
of the 23 channels on the radio receiver.)

3.   To program the CLOSE button to a remote control press and 

release the CLOSE button on the logic board. The RADIO LED 
will flash and then stay on solid. Then press the corresponding 
button on the remote control. The RADIO LED on the logic 
board will flash, this confirms that the remote control has been 
programmed. (By programming the remote you use 1 channel 
of the 23 channels on the radio receiver.)

4.   To program the STOP button to a remote control press and 

release the STOP button on the logic board. The RADIO LED 
will flash and then stay on solid. Then press the corresponding 
button on the remote control. The RADIO LED on the logic 
board will flash, this confirms that the remote control has been 
programmed. (By programming the remote you use 1 channel 
of the 23 channels on the radio receiver.)

5.   After learning remote controls press the RADIO button on the 

logic board (RADIO LED will turn off). 

NOTE:

 If no activity 

within 30 seconds the radio will automatically exit 
programming mode.

SLO

T    1

RADIO

SLS

MRT

MID

TTC

DATA

24VAC

24VAC

LMEP:

EDGE:

OPEN

CLOSE

STOP

COMMON

RELAY    A

RELAY    B

SBC

MAS

COMMON

TIMER

DEFEAT

POWER

TIMER

ENABLE

1

2

3

FSTS

DIAG

OPTN

PROG

T

TS

E2

D1

C2

B2

CLS

OLS

MID

REV

STD

SLO

T    2

MO

T

OR

DIRECTION

3-PHASE

1-PHASE

EDGE:

OPEN

CLOSE

STOP

COMMON

MER

NABLE

OPEN 

CLOSE 

STOP 

Open

Close

Stop

REMOTE CONTROL PROGRAMMING FEATURE
Program Remote Controls from the 3-button control station 
(3BCS).

This feature allows the user to add additional remote controls 
from the 3BCS. By default the remote control learn option is off. 

NOTE: 

Requires access to the operator electrical box to enable or 

disable this feature.

To turn this feature on:

1.   Turn the SELECTOR DIAL to PROG.
2.   Press and release the RADIO button. The RADIO LED will be lit.
3.   Press and release the MID button. The RADIO LED will flash 

quickly 6 times.

4.   Press and release the RADIO button. The RADIO LED will turn 

off.

5.   Return the SELECTOR DIAL to the desired wiring type.

To add remote controls from the 3BCS:

1.   With the door in the fully closed position (close limit activated), 

press and hold STOP.

2.   While holding STOP, press and hold CLOSE.
3.   While holding STOP and CLOSE, press and hold OPEN.
4.   Release all three buttons once the MAS LED has lit.
5.   Learn a remote control by one of the following methods:
 a.   

Programming 

a 

standard single button/single function 

remote control,

 push and hold the remote control button 

until the MAS LED goes out. Repeat steps 1 through 4 to 
add additional remote controls.

 b.   

Programming 

a 

3-button/three function remote control 

(OPEN/CLOSE/STOP), first push the button on the 3BCS 
(Example: OPEN) and then press and hold the button on 
the remote control (Example: large button) that you want 
to correspond with the selected (Example: OPEN) 
command until the MAS LED flashes and goes out. 
Repeat steps 1 through 4 to add additional buttons 
(CLOSE AND STOP).

To turn this feature off:

1.   Turn the SELECTOR DIAL to PROG.
2.   Press and release the RADIO button. The RADIO LED will be lit.
3.   Press and release the MRT button. The RADIO LED will flash 

quickly 3 times.

4.   Press and release RADIO button. The RADIO LED will turn off.
5.   Return SELECTOR DIAL to desired wiring type.

NOTE: 

Restoring the operator to Factory Default (see RESETTING 

FACTORY DEFAULTS) will also disable this feature. The remote 
controls will still be learned.

Programming - Remote controls

PROGRAMMING REMOTE CONTROLS

Содержание GH













































Отзывы:

Нет отзывов

Похожие инструкции для GH

Aalborg SMV Operating Manual preview
SMV
Бренд: Aalborg Страницы: 15
Aalborg DFC Operating Manual preview
DFC
Бренд: Aalborg Страницы: 48
Lattice Semiconductor HDR-60 User Manual preview
HDR-60
Бренд: Lattice Semiconductor Страницы: 26
Datavideo RMC-230 Instruction Manual preview
RMC-230
Бренд: Datavideo Страницы: 17
Datamax I-Class Installation And Operating Instructions Manual preview
I-Class
Бренд: Datamax Страницы: 22
Easy-Laser E540 Manual preview
E540
Бренд: Easy-Laser Страницы: 84
Easy Heat RS2 Installation And Operation Instructions preview
RS2
Бренд: Easy Heat Страницы: 4
National Instruments 9853 Getting Started Manual preview
9853
Бренд: National Instruments Страницы: 29
Lab.gruppen LAB.LEVEL4 Quick Start Manual preview
LAB.LEVEL4
Бренд: Lab.gruppen Страницы: 2
LMI Technologies Liquitron DP5000-01A Instruction Manual preview
Liquitron DP5000-01A
Бренд: LMI Technologies Страницы: 28
Motrona CA306 Operating Manual preview
CA306
Бренд: Motrona Страницы: 10
Pilz PSS67 IO1 16FDI Operating Manual preview
PSS67 IO1 16FDI
Бренд: Pilz Страницы: 36
DSEGenset DSE8003 MKII Operator'S Manual preview
DSE8003 MKII
Бренд: DSEGenset Страницы: 74
ITALFARAD RC4 Operating Instructions Manual preview
RC4
Бренд: ITALFARAD Страницы: 32
Comet S0841 Instruction Manual preview
S0841
Бренд: Comet Страницы: 9
Hattersley C31 Installation And Operating Instructions preview
C31
Бренд: Hattersley Страницы: 2
National Instruments PXIe-6595 Getting Started Manual preview
PXIe-6595
Бренд: National Instruments Страницы: 6
One for All Kameleon User Manual preview
Kameleon
Бренд: One for All Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды