Chamberlain CSW200UL8 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 52

Chamberlain CSW200UL8 Скачать руководство пользователя страница 28

26

NOTE:

If the photoelectric sensor gets blocked while the gate is

closing, it will stop and reopen. The gate will remain open until
the obstruction is cleared.

Contact your local dealer for more information about photoelectric sensors.

Safety Non-Contact Sensor

Entrapment Non-Contact Sensor

To prevent SERIOUS INJURY or DEATH from a moving gate:
• Locate entrapment protection devices to protect in BOTH the

open and close gate cycles.

• Locate entrapment protection devices to protect between

moving gate and RIGID objects, such as posts or walls.

Non-Contact Sensors (12 Vdc Photoelectric Sensors)

NOTE:

Property owners are obligated to test photoelectric sensors

monthly.

See Accessories for part number.

It is best to use Failsafe Photoelectric Sensors for
this safety option.
Failsafe Photoelectric Sensors:

If a failsafe

photoelectric sensor is not working or loses power
or photoelectric sensor is blocked, then the
photoelectric sensors will stop ALL gate operation.

WIRING

ENTRAPMENT PROTECTION DEVICES

«
...
26
27
28
29
30
...
»

Содержание CSW200UL8





















































Отзывы:

Нет отзывов