Chamberlain C2212T страница 40 Скачать руководство пользователя | Manualshive

Страница: 40 / 52

background image

40

Operation

Remote Control and Keyless Entry

PRE-PROGRAMMED REMOTE CONTROL INCLUDED, NO NEED TO PROGRAM THE
REMOTE.

To add or reprogram a remote control, follow the instructions below. Older Chamberlain remote controls are
NOT compatible.

PROGRAM USING THE MULTI-FUNCTION CONTROL PANEL

1.

Press the LEARN button on the door control to enter programming mode. The command LED will flash
once.

2.

Press the LEARN button again, the command LED will flash once again.

3.

Remote Control:

Press the button on the remote control that you wish to operate your garage door.

Keyless Entry:

Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry

keypad. Then press the ENTER button.

PROGRAM USING THE PUSH BUTTON DOOR CONTROL

1.

Press and hold the light button and the push button until the push button LED begins to blink.

2.

Remote control:

Press the button on the remote control that you wish to operate your garage door.

Keyless entry:

Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry

keypad. Then press the ENTER button.

PIN

OR

?

?

?

?

Push

Button

LIGHT

Button

The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.
Repeat the steps for programming additional remote controls or keyless entry devices. If programming is
unsuccessful, follow the steps to program using the garage door opener LEARN button.

PROGRAM USING THE GARAGE DOOR OPENER LEARN BUTTON

1.

Locate the LEARN Button.

2.

Press and immediately release the LEARN button. The LEARN LED will glow steady for 30 seconds.
Within 30 seconds...

3.

Remote Control:

Press and hold the button on the remote control that you wish to use.

Keyless Entry:

Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry

keypad. Then press and hold the ENTER button.

Release the button when the garage door opener lights blink or two clicks are heard.

“click”

“click”

PIN

OR

1-2

3

LEARN LED

LEARN

Button

HomeLink®

If your vehicle is equipped with HomeLink®, a Compatibility Bridge™ (not included) may be necessary for
certain vehicles. Visit bridge.chamberlain.com to find out if a Bridge is needed.

«
...
38
39
40
41
42
...
»

Содержание C2212T





















































Отзывы:

Нет отзывов

Похожие инструкции для C2212T

Бренд: Viking Страницы: 48

Бренд: Novoferm tormatic Страницы: 43

Бренд: SOMFY Страницы: 72

Бренд: Nice Страницы: 16

Бренд: Nice Страницы: 31

Бренд: Nice Страницы: 20

Бренд: Nice Страницы: 184

Бренд: Nice Страницы: 98

Бренд: Nice Страницы: 148

Бренд: Boss Страницы: 23

CARDIN ACE FAST

Бренд: Riello Elettronica Страницы: 20

Бренд: tau Страницы: 8

Бренд: USAutomatic Страницы: 44

Бренд: Dea Страницы: 140

Бренд: HYDOM Страницы: 12

Бренд: FAAC Страницы: 27

Dynamic Dolphin Remote

Бренд: Quantum Страницы: 8

Бренд: gebatronic Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды