Chamberlain C2212T страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 52

background image

23

Installation

STEP 9 Connect the Door Arm to the Trolley (continued)

OPTION B - ONE-PIECE DOORS

IMPORTANT:

The groove on the straight door arm MUST face away from the curved door arm.

1.

Close the door. Disconnect the trolley by pulling the emergency release handle.

2.

Fasten the straight door arm and the curved door arm together to the longest possible length (with a 2
or 3 hole overlap) using the bolts, nuts, and lock washers.

3.

Attach the straight door arm to the door bracket using the clevis pin. Secure with the ring fastener.

4.

Attach the curved door arm to the trolley using the clevis pin. Secure with the ring fastener.

5.

Pull the emergency release handle toward the garage door opener until the trolley release arm is
horizontal.

HARDWARE

Hex Bolt 5/16"-18x7/8"

Nut 5/16"-18

Lock Washer
5/16" -18

Clevis Pin 5/16"x1"

Clevis Pin 5/16"x1-1/4"

Ring Fastener

One-Piece Door without Track

One-Piece Door with Track

Ring Fastener

Ring Fastener

Ring Fastener

Nut

Nut

Ring Fastener

Lock Washer

Lock Washer

Clevis Pin 5/16"x1-1/4"

Clevis Pin
5/16"x1-1/4"

Hex Bolts

Hex Bolts

Clevis Pin
5/16"x1"

Clevis Pin
5/16"x1"

Straight Door Arm

(Groove facing out)

Curved Door Arm

«
...
21
22
23
24
25
...
»

Содержание C2212T





















































Отзывы:

Нет отзывов

Похожие инструкции для C2212T

Бренд: FAAC Страницы: 27

Бренд: FAAC Страницы: 14

Бренд: Garageio Страницы: 2

Бренд: Chamberlain Страницы: 29

Бренд: Chamberlain Страницы: 40

Бренд: CAME Страницы: 30

Бренд: Topens Страницы: 22

Бренд: GBD Страницы: 8

Бренд: Key Automation Страницы: 88

Бренд: Black & Decker Страницы: 8

Gizmo EM200 Series

Бренд: Black & Decker Страницы: 2

Бренд: Wisniowski Страницы: 22

Бренд: Wisniowski Страницы: 48

76380 - Classic Chrome Heavyweight Can...

Бренд: Hamilton Beach Страницы: 5

Бренд: Automatic Solutions Страницы: 14

Бренд: Automatic Страницы: 36

AMICO Series A1824

Бренд: CAME Страницы: 12

Бренд: Chamberlain Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды