Challenger Lifts SX14, Инструкция по установке, эксплуатации и обслуживанию, Страница: 16 / 46

16
V
ERTICAL
C
LEARANCE
Check the height of the area where the lift is to be
installed. Clearance should be calculated based on
the full raised height of the lift.
Failure by purchaser to provide
adequate clearance could result in
unsatisfactory lift performance,
property damage, or personal injury.
F
LOORING
Be certain you have the proper concrete floor
to properly handle the loaded lift. Floor
should be in generally good condition with no
large cracks, spalling or deterioration.
Minimum requirements for concrete are 6 inches
minimum depth, with steel reinforcement, 3500
psi, cured for 28 days per local commercial
practice. Floor should be level within 3/8 inch over
the installation area. No anchors should be
installed within 6 inches of any crack, edge, or
expansion joint. If these conditions cannot be
met, a pad may be poured to accommodate the
lift.
Check with local building inspectors and/or
permits office for any special instructions or
approvals required for your installation.
Failure by purchaser to
provide the recommended
mounting surface could
result in unsatisfactory lift performance, property
damage, or personal injury.
L
OCATION
This lift is approved for indoor use only.
E
LECTRICAL
R
EQUIREMENTS
For lift installation and operation it is
necessary to have a dedicated circuit with
circuit breaker or time delay fuse. Refer to
Fig. 15 for circuit sizing.
S
AFETY
N
OTICES AND
D
ECALS
For your safety, and the safety of others, read and
understand all of the safety notices and decals
included in this manual.
R
EAD ENTIRE MANUAL BEFORE ASSEMBLING
,
INSTALLING
,
OPERATING
,
OR SERVICING THIS
EQUIPMENT
.
P
ROPER MAINTENANCE AND INSPECTION IS
NECESSARY FOR SAFE OPERATION
.
DO NOT
OPERATE A DAMAGED LIFT
.
Safety decals similar to those shown in this manual
are found on a properly installed lift. Be sure that all
safety decals have been attached to the control
console of the lift. Verify that all authorized
operators know the location of these decals and
fully understand their meaning. Replace worn,
faded, or damaged decals promptly.
Do not attempt to raise a vehicle on
the lift until the lift has been
correctly installed and adjusted as
described in this manual.
R
ECEIVING
The shipment should be thoroughly inspected as
soon as it is received. The signed bill of lading is
acknowledgement by the carrier of receipt in good
condition of shipment covered by our invoice.
If any of the goods called for on this bill of lading are
shorted or damaged, do not accept them until the
carrier makes a notation on the freight bill of the
shorted or damaged goods. Do this for your own
protection.
NOTIFY
Challenger Lifts
AT ONCE if any
hidden loss or damage is discovered after receipt.
IT IS DIFFICULT TO COLLECT FOR LOSS OR
DAMAGE AFTER YOU HAVE GIVEN THE
CARRIER A CLEAR RECEIPT.
File your claim with
Challenger Lifts
promptly.
Support your claim with copies of the bill of lading,
freight bill, and photographs, if available.
H
ANDLING
The packaged lift must only be transported
and handled using dedicated hoisting
equipment with a greater capacity than the lift
to be handled. Lifting straps should be used
during installation of lift. Weight of packaged
lift and accessories can be
approx 6000 lbs .
A
CCEPTED
O
ILS
–
Do not use oils with
detergents. Hydraulic fluid is not provided with
the lift shipment.
-10 wt. anti-foam, anti-rust
hydraulic / biodegradable oil
-Dexron III ATF
T
OOLS
(
MINIMUM REQUIRED
)
a. Tape measure, 16ft
b. Chalk
line
c. 4ft level
d. 10” adjustable wrench
e. Standard open end wrenches 5/16”, 3/4”
f. Allen wrench set
g. Hammer drill with 1/4” & 1/2” diameter
carbide tipped bits
h. 2lb hammer
i. Torque wrench: 50 foot-pounds minimum
with 3/4” socket
j. Screwdriver
k. Long oil funnel
I
MPORTANT
:
Always wear safety glasses
while installing lift.
S
URFACE
& F
LUSH
M
OUNT
L
AYOUT
WARNING
WARNING
WARNING