background image

1.0  Introduction 

 

 
2

 

1.0 Introduction 

THIS MANUAL is designed to help you get the most from your Challenge equipment.  Keep this 
manual in a safe, convenient place for quick reference by operators and service personnel. 
 

 SAFETY ALERT!  This symbol means CAUTION: Personal safety 

instructions!  Pay special attention to the instructions in bold type.  Personal injury may result if the 
precautions are not read and followed. 
 
 
READ THIS MANUAL BEFORE OPERATING!  Follow precautions and instructions given and you 
should have years of trouble-free operation.  If after reading the manual questions still remain, contact 
your Authorized Challenge Dealer. 
 
FOR PARTS AND SERVICE contact the Authorized Challenge Dealer from whom you purchased 
your machine.  Use the illustrations and parts lists at the back of this manual to identify the correct 
parts needed.  Always give the SERIAL NUMBER and MODEL of your machine to insure the correct 
parts are sent as soon as possible. 
 
Take a few minutes right now to RECORD YOUR MACHINE SERIAL NUMBER in the space 
provided on the front cover of this manual.  Also be sure to fill out the warranty card accompanying 
your machine and return it DIRECTLY TO CHALLENGE. 
 
If you bought a used machine, it is important to have the following information on record at Challenge.  
Copy this page, fill in the information and send it care of The Challenge Service Department, 6125 
Norton Center Dr. 

 Norton Shores 

 MI  49441-6081.  

 
 

CHALLENGE MODEL   

SERIAL NUMBER 

ATTN COMPANY 
 
ADDRESS 
CITY STATE/PROVINCE 

ZIP 

PHONE DATE 

INSTALLED 

DEALER NAME & CITY 

 

 
 

* WARRANTY INFORMATION * 

 

It is very important that you read and understand the conditions outlined in the Warranty Information 
Sheet 
attached to the outside of the shipping container of your machine. 
 
The Warranty Information Sheet must be filled out completely and returned to THE CHALLENGE 
MACHINERY COMPANY in order for the warranty to be issued for this machine. 

 

 
 
 
 
 
Challenge® is a registered trademark of The Challenge Machinery Company

6125 Norton Center Dr.

 Norton Shores MI 

49441-6081 Copyright© 1999-2013 by The Challenge Machinery Company.  All rights reserved.  Printed in the U.S.A 

Содержание CH-EH3






























Отзывы: