manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 85

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

2-73 

2. Status Indicator RAPs

 

RAP 2.65 Elevator Pusher Interlock 

The pusher interlock prevents any movement of 
the lift plates when the pusher is not completely 
retracted and in its home position.  The switch is 
located near the pusher cylinder under the top 
plate (Figure 2-102). 

Possible Fault Indicators 

 

“Elevator Book Push Error”

 

message is displayed. 

Initial Actions 

Check that all cables between the trimmer, Ele-
vator, and Tilt Infeed Conveyor are securely fas-
tened and are not damaged. 

Check and repair loose or damaged wires 24 
and 25 at the Elevator electrical panel (Figure 
2-103) and at the interlock switch. 

Procedure 

1.  Switch the main power ON and main air ON.  

Is the pusher cylinder completely retracted 
and in its home position? 

Y  N 

Go to RAP 2.56 Elevator Pusher Cylinder. 

2.  Press the green start button to initialize the 

trimmer.  Remove the Elevator motor cover 
to access the Elevator electrical panel. Is 
there 120 VAC between wire 24 at circuit 
breaker CB1 and wire 22 at the electrical 
panel? 

Y  N 

Go to RAP 2.55 Elevator Lift Motor. 

3.  With the hydraulic motor still running, is 

there 120 VAC between wire 25 at SSR1 
and wire 22 at the electrical panel? 

Y  N 

Adjust pusher interlock switch so that it the 
actuator is depressed properly when pusher 
cylinder is retraced.  If problem still exists, 
replace defective switch (PL 5.29 Elevator 
56421TCA (2/7)). 

4.  Go to the Elevator diagnostic screen (GP 

6.2 Input/Output Diagnostics) and enable 
outputs.  Switch on output “Book Push”.  
Does the pusher cylinder move toward the 
trimmer completely? 

Y  N 

Go to RAP 2.56 Elevator Pusher Cylinder. 

5.  With the hydraulic motor still running, is 

there 0 VAC between wire 25 at SSR1 and 
wire 22 at the electrical panel? 

Y  N 

Replace defective switch (PL 5.29 Elevator 
56421TCA (2/7)). 

Repair Complete. 

 

Figure 2-102. Elevator Pusher Interlock 

 

Figure 2-103. Elevator Electrical Panel 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды