Challenge 130TC-A-160000 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 282

background image

MAY 2019

2. Status Indicator RAPs

2-64

CMT-130TC Book Trimmer

RAP 2.56 Elevator Pusher Cylinder

Elevator I/O PWB Output 1

The Elevator pusher cylinder feeds the book
from the top shelf of the Elevator into the trim-
mer. The cylinder is mounted to the underside
of the top frame plate in the Elevator.

Possible Fault Indicators



Book does not leave Elevator and trav-
els over the top.



Pusher remains extended, never ex-
tends, or extends erratically.

Initial Actions

Perform RAP 2.20 Pneumatic Pressure.

Check that all cables and air tubing between the
trimmer, Elevator, and Tilt Infeed Conveyor are
securely fastened and are not damaged.

Perform GP 6.14 Speed-Control Air Valves.

Check that all air hoses inside the Elevator are
connected properly and not damaged or
pinched.

Check for loose or broken wire 50 at the Eleva-
tor electrical panel.

Check that the cable connector on the air valve
is connected properly.

Procedure

1. Open the Elevator door and fully open the

flow control valve on the left end of the
pusher air cylinder (Figure 2-83).

2. Pull the Elevator away from the machine to

access the flow control on the right side of
the Elevator. Fully open the flow control
valve on the right side.

3. Manually activate the air valve by pressing

the actuator button on the valve (Figure
2-84). Does the pusher extend?

Y N

Disconnect power and air and replace the
air valve (PL 5.37 Elev. Electrical Panel EE-
3523).

4. Electrically activate the air valve by shorting

wire 50 to wire 74. Does the pusher ex-
tend?

Y N

Disconnect power and air and replace the
air valve (PL 5.37 Elev. Electrical Panel EE-
3523).

5. Disconnect main power and replace the Ele-

vator I/O PWB (REP 4.26 Accessory PWB
Replacement).

6. Readjust the flow control valves to cushion

the stop at the end of the stroke in each di-
rection. Be careful not to over-restrict the
flow because it will cause erratic travel at the
end of the stroke.

Figure 2-83. Elevator Pusher

Figure 2-84. Pneumatic Valve

«
...
74
75
76
77
78
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Yard-Man Страницы: 64

Бренд: MPM Страницы: 24

Бренд: Worx Страницы: 16

Бренд: Yard-Man Страницы: 56

Бренд: Tanaka Страницы: 26

Бренд: Okay Страницы: 36

Бренд: Beper Страницы: 48

Бренд: PRETUL Страницы: 24

Бренд: City Theatrical Страницы: 8

Бренд: Talon Страницы: 6

Бренд: McCulloch Страницы: 1

Бренд: Yamabiko Страницы: 64

Бренд: McCulloch Страницы: 13

Бренд: Haussmann Страницы: 22

Бренд: Haussmann Страницы: 24

Бренд: Haussmann Страницы: 28

Бренд: Titan Страницы: 56

Бренд: Powerplus Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды