Challenge 130TC-A-160000 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 282

background image

MAY 2019

2. Status Indicator RAPs

2-72

CMT-130TC Book Trimmer

RAP 2.64 Elevator Pusher Home Sen-
sor

Elevator I/O PWB Input 11

The pusher home sensor detects when the
pusher cylinder is in its home position (com-
pletely retracted). This sensor is used to pre-
vent the lift plates from lifting whenever the
pusher is not in its home position. The sensor is
attached to the pusher cylinder (Figure 2-100).

Possible Fault Indicators



“Elevator Book Push Error”

message is displayed.

Initial Actions

Check that all cables between the trimmer, Ele-
vator, and Tilt Infeed Conveyor are securely fas-
tened and are not damaged.

Check and repair loose or damaged wires 46,
73, and 74 at the Elevator electrical panel (Fig-
ure 2-101).

Procedure

1. Switch the main power ON and main air ON.

Is the pusher cylinder completely retracted
and in its home position?

Y N

Go to RAP 2.56 Elevator Pusher Cylinder.

2. Go to the Elevator diagnostic screen (GP

6.2 Input/Output Diagnostics). Is input
“Pusher Home” on?

Y N

Short wire 46 to 74. On the diagnostic
screen does input “Pusher Home” switch
on?

Y N

Disconnect power and replace the Ele-
vator I/O PWB (REP 4.26 Accessory
PWB Replacement).

Adjust either the sensor or actuator magnet
by loosening set screw in sensor or magnet
and slide sensor or magnet until input
comes on. If input still does not come on, re-
place defective switch (PL 5.37 Elev. Electri-
cal Panel EE-3523).

3. Go to the Elevator diagnostic screen (GP

6.2 Input/Output Diagnostics) and enable
outputs. Switch on output “Book Push”.
Does the pusher cylinder move toward the
trimmer completely?

Y N

Go to RAP 2.56 Elevator Pusher Cylinder.

4. On the diagnosti

c screen is input “Pusher

Home” off?

Y N

Disconnect wire 46. On the diagnostic
screen does input “Pusher Home” switch
off?

Y N

Disconnect power and replace the Ele-
vator I/O PWB (REP 4.26 Accessory
PWB Replacement).

Replace defective switch (PL 5.37 Elev.
Electrical Panel EE-3523).

Repair complete.

Figure 2-100. Elevator Pusher Home Sensor

Figure 2-101. Elevator Electrical Panel

«
...
82
83
84
85
86
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Wireless Outlet Dimmer

Бренд: Control 4 Страницы: 2

Бренд: EarthWise Страницы: 24

Бренд: Gardena Страницы: 17

Бренд: Snapper Страницы: 12

Бренд: Brother Страницы: 236

Бренд: Yardworks Страницы: 10

Бренд: Yardworks Страницы: 64

Бренд: Yard Machines Страницы: 24

Бренд: Yard force Страницы: 29

Бренд: Scotts Страницы: 34

Бренд: TUPANAT Страницы: 9

Бренд: TEM Страницы: 2

Бренд: IBEA Страницы: 48

Бренд: IBEA Страницы: 76

Бренд: GreenWorks Pro Страницы: 28

Бренд: sunjoe Страницы: 20

Бренд: Philio Technology Corporation Страницы: 6

Бренд: Yard force Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды