Challenge 130TC-A-160000 Скачать руководство пользователя страница 139

Страница: 139 / 282

MAY 2019

CMT-130TC Book Trimmer

4-33

4. Repair/Adjustment Procedures

ADJ 4.28 Elevator Shelf Synchroniza-
tion

Any time the Elevator

’s drive chain or drive mo-

tor is replaced, the Elevator lift plates will require
synchronization.

Initial Actions

WARNING

Disconnect and lockout power as described
in the Power Lockout Procedure on page ix.

Disconnect the Elevator from the trimmer. Re-
move the lower right-hand side cover from the
Elevator that covers the drive chain (Figure
4-46).

Procedure

1. Switch the main power OFF and lockout

power to the machine. Switch the main air
OFF.

2. Use a hex allen wrench to loosen the two

setscrews that mount the left-hand sprocket
to the shaft (Figure 4-47). Back the set-
screws out approximately 1/2" (12 mm).

3. Thread a 3/8-16 screw (from toolkit) into the

open hole in the sprocket hub.

4. Turn the screw until the insert disengages

from the sprocket hub.

5. Remove the insert removal screw from the

hub.

6. Raise the Elevator lift plates on the free side

until they are level with the plates on the op-
posite side (Figure 4-48).

7. With the plates level, rotate the adjustment

hub counterclockwise by hand to put tension
on the chain (Figure 4-49).

8. Using a hammer or mallet, gently tap the in-

sert into the sprocket hub while maintaining
tension in the chain.

9. Tighten the two setscrews in the adjustment

hub to lock it in place.

10. Repeat this procedure as necessary, until

the plates are level and the drive chain is
under tension. If the drive chain is not under
tension, the plates will lose synchronization
as soon as the motor is switched on.

11. Re-install all covers and attach the Elevator

to the trimmer.

Figure 4-46. Adjustment Sprocket

Figure 4-47. Loosen Adjustment Hub

Figure 4-48. Level the Lift Plates

Figure 4-49. Tension Drive Chain

Содержание 130TC-A-160000



























































































































































































































































































Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Похожие инструкции для 130TC-A-160000

Бренды по названию

Популярные бренды

Challenge 130TC-A-160000, Руководство по обслуживанию

Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Похожие инструкции для 130TC-A-160000

Бренды по названию

Популярные бренды