Challenge 130TC-A-160000 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 282

background image

MAY 2019

CMT-130TC Book Trimmer

3-3

3. Book Quality

BQ 3.2 Burr Marks

Description

Burr marks are found on books trimmed with a
knife that has a burred cutting edge. Figure 3-1
illustrates the appearance of burr marks.

Figure 3-1. Burr Marks

Possible Causes



Burrs on knife can occur from improper
knife handling.



Burrs may also occur from cutting hard,
irregular materials, or books with sta-
ples.

Solutions



Replace the knife (REP 4.2 Knife Re-
placement).

BQ 3.3 Jagged Bottom Cover

Description

Books can appear as though the bottom few
sheets and cover were torn apart rather than
sharply cut. Tearing of the bottom sheets and
cover occur when deep score marks develop in
the cut stick. The cover is pushed into the score
mark, folded over and torn.

Figure 3-2. Jagged Cover

Possible Causes



The cut stick may be worn.



The knife may be dull.

Solutions



Rotate or replace the cut stick (REP 4.1
Cut Stick Replacement).



Replace the knife (REP 4.2 Knife Re-
placement).

BQ 3.4 Burr Marks/Jagged Cover

Description

A jagged bottom cover may also accompany
burr marks. A burred knife may not fully cut into
the cut stick. As a result, it will leave a jagged
bottom cover.

Figure 3-3. Burr Marks/Jagged Cover

Possible Causes



The knife is burred, and the cut stick is
worn.

Solutions



Rotate or replace the cut stick (REP 4.1
Cut Stick Replacement).



Replace the knife (REP 4.2 Knife Re-
placement).

«
...
101
102
103
104
105
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: LAWN STAR Страницы: 12

Бренд: Recharge Tools Страницы: 14

Бренд: Kobalt Страницы: 45

Бренд: Scheppach Страницы: 68

Бренд: Ozito Страницы: 8

Бренд: EarthWise Страницы: 30

Бренд: Tanaka Страницы: 72

Yellow GARDEN LINE YGL N.G. 32/2

Бренд: Zgonc Страницы: 32

Бренд: Gardena Страницы: 9

Бренд: Gardena Страницы: 14

Бренд: Parkside Страницы: 60

Бренд: Parkside Страницы: 94

PAS-225SB Pro Attachment Series

Бренд: Echo Страницы: 36

Бренд: Makita Страницы: 76

Бренд: Hitachi Страницы: 178

Бренд: Eckman Страницы: 9

Бренд: Eckman Страницы: 12

Бренд: Eckman Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды