manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 109

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

4-3 

4. Repair/Adjustment Procedures

 

REP 4.2 Knife Replacement 

WARNING 

Changing knives can be very dangerous un-
less safety precautions are observed and ex-
treme care is taken when handling knives.  
Keep handling of unprotected knives to an 
absolute minimum.  Have the scabbard 
nearby and insert knife immediately.  Warn 
people of any unprotected knife. 

WARNING 

Knife changing is a ONE PERSON OPERA-
TION!  More than one person changing a 
knife creates safety hazards. 

WARNING 

Even used knives are extremely sharp!  Use 
extreme care when handling new, re-ground, 
and used knives. 

WARNING 

Disconnect and lockout power as described 
in the Power Lockout Procedure on page ix. 

Initial Actions 

Locate a stable cart or table approximately 36" 
tall, the knife lifter, the T-handle hex wrench, an 
empty scabbard, and a sharp knife (Figure 4-4). 

 

Figure 4-4. Knife Replacement Supplies 

Knife Removal Procedure 

1.  Switch the main power OFF and lockout 

power to the machine. 

2.  Move the waste bin aside and open the rear 

door. 

3.  Place an empty scabbard on a nearby, sta-

ble surface. 

4.  Using the T-handle hex wrench, remove the 

two

 knife bolts that are in 

open slots

 in the 

knife bar (Figure 4-5).  They are the second 
and sixth bolts from either end of the knife.  
Set the bolts aside and save for knife instal-
lation. 

 

Figure 4-5. Knife Bolt Locations 

5.  Place the knife lifter in position, aligning 

each lifter handle with the holes from which 
the two knife bolts were removed in the pre-
vious step.  Turn the handles clockwise until 
the lifter is securely fastened to the knife bar 
(Figure 4-6). 

 

 

Figure 4-6. Knife Lifter 

6.  Use the T-handle wrench to remove the re-

maining (5) knife bolts.  Save the bolts with 
the two previously removed. 

WARNING 

Make certain to have a scabbard on the cart, 
prepared to receive a knife.  The screws 
should be removed from the scabbard.  The 
protecting edge of the scabbard should be 
facing the person changing the knife when 
placing the knife in it.  Make sure the cart is 
nearby.  Do not carry the knife across ob-
structed or slippery floors.  Warn people 
nearby that a knife is being removed. 

7.  Slowly turn the knife lifter handles counter-

clockwise only until the knife is released 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды