appliance. Use only hoses, fittings and couplings recommended by the manufacturer.
- Do not use the appliance if a
supply cord
or important parts of the appliance are damaged, e.g.
safety devices, high pressure hoses,
trigger gun
.
-
WARNING
: If an extension cord is used, the plug and socket must be of watertight
construction.
-
WARNING
: Inadequate extension cords can be dangerous.
- This high pressure washer must not be used at temperatures below 0°C.
WARNING!
- Cord on drums should always be completely extended to prevent the cord from overheating.
- If an extension cord is used, the plug and socket must be of watertight construction.
- Inadequate extension cords can be dangerous.
- Power cord connections should be kept dry and off the ground.
- If the power cord is damaged, it must be replaced by the manufacturer or his service agent or
similarly qualified person in order to avoid a hazard.
- Always ensure the machine is on a flat level surface and is stable. Never tip the machine on
one side.
In the event of accident or breakdown, switch off the machine immediately. (e.g. contact with
detergent: rinse with an abundance of clean water)
WARNING!
ELECTRICAL SHOCK HAZARD
To reduce the risk of electrocution, you keep all connections dry and off the ground. You do
not touch the plug with wet hands. The electric supply connection shall be made by a qualified
electrician and comply with IEC 60364-1.
Mains power connection
The following should be observed when connecting the high pressure
washer to the electric installation:
- The electric installation shall be made by a certified electrician and comply with IEC-364.
- It is recommended that the electric supply to this appliance should include either a
residual current device that will interrupt the supply if the leakage current to earth exceeds
30 mA for 30 ms.
IMPORTANT! Only use water without any impurities.
- The water inlet fi lter must be inspected regularly, so as to avoid blockage and restriction in
the water supply to the pump.
Safety devices
- The pressure washer is equipped with an auto stop device. When the trigger is released it will
open the power circuit to the motor and cause the pressure washer motor to stop.
Thermal sensor:
- A thermal sensor protects the motor against overloading. The machine will restart after a few
minutes when the thermal sensor has cooled.
5. NAME OF PARTS: (FIG. 1)
1. Wheel
5. Screw
9. Support of hose
13. Spray Handle
2. Water Inlet Connector
6. Support of lance
10. Plug/cable
14. Lance
3.Filter
7. Bottle Assembly
11. High Pressure Hose
15.Nozzle Cleaning Needle
4.Housing
8. Handle
12. Safety lock
6. PRODUCT DESCRIPTION
PURPOSE
z
The high pressure cleaner is designed to clean vehicles, machines, buildings, facades, etc.
in the private sector.
AREAS OF APPLICATION
z
Never use the machine in potentially explosive areas under any circumstances!
z
The operating temperature must be between 0 and +40
.
℃
z
The machine consists of an assembly with a pump, which is encased in a shock absorbing
housing. For an optimal working position the machine comes with a lance and a non-slip
handle grip, whose shape and configuration comply with the applicable regulations.
z
Do not cover or modify the lance or the spray nozzles in any way.
z
The high pressure cleaner is designed to be used with cold or lukewarm (max. 60
);
℃
higher temperatures can damage the pump.
z
Do not use water that is dirty, gritty or contains any chemical products, as these could
impair operation and shorten the life of the machine.
z
Accessories can be used to carry out work with foam cleaners, sand spraying.
7. ASSEMBLY
z
Position the washer as
NEAR
as possible to the water supply.
z
Always ensure the machine is on a flat level surface and is stable. Never tip the machine on
one side. FIG.2.
z
Fit the lance into the gun and rotating it until the two parts are completely locked FIG. 3.
z
Connect the gun to the high pressure hose FIG.4.
z
Connect the high pressure hose to the water outlet on the washer FIG. 5.
z
Connect the water supply hose to female coupler FIG.6, then connect to the water inlet of
the washer. The supply hose must have an internal diameter of at least 13mm (1/2 in.) and
must be reinforced. The water supply must be at least equal to the washer delivery
capacity.
z
NOTE: The machine not suitable for connection to the potable water main (FIG. 16).
WARNING
The intake water temperature must not exceed 40
℃
. The water supply must not exceed
0.7 MPa.
