manualshive.com logo in svg

CES M-20 Repeater Maker plus, Инструкция по установке и эксплуатации

Поделиться
Скачать
CES M-20 Repeater Maker plus Скачать руководство пользователя страница 13

CES SUPPORT 407-679-9440               

Page  13

MAN79 ©  CES 2009

3.0  Programming Procedures

3

.1 Programming the RM-20

Programming procedures

The model RM-20 can be easily programmed locally with a standard DTMF telephone. Programming can also be 

achieved “over the air” with a DTMF microphone.

Note:  Programming over the air requires a program access code. This code must be programmed locally on initial 
installation.

Local programming

Local programming is accessed by plugging a DTMF telephone handset into the programming jack (J1) on the rear 
panel of the RM-20. To access the local program mode, turn the power off and back on and press the * (asterisk) 
key within two seconds of applying power to the unit. The RM-20 will generate a series of beeps to the 
programming 

telephone earpiece

acknowledging the program mode entry. An easy way to insure that the * is 

received within 2 seconds is to have the * key pressed as power is applied, then release it as soon as the tone is 
heard.

Over the Air programming

The model RM-20 can also be programmed over the air using a DTMF microphone or a portable radio equipped 

with DTMF keypad. However an “over the air” program code (up to 9 digits) must be programmed into the unit. It 
is suggested that this code is programmed on initial installation. Once an “over the air” programming code is 
programmed, the RM-20 can be easily accessed and programmed over the air. Simply send the access code 
accompanied by carrier and monitor the transmitter frequency. If successfully entered in the program mode a series 
of beeps will be heard. Proceed to enter the program codes needed to be programmed by pressing each key slowly 
and firmly and monitor the frequency for the acknowledge tones. The programming code entry sequence is exactly 
the same as in local programming mode. Once the unit is programmed, press (00#) to exit the program mode.

To assist the programming process, a number of confidence toned will heard. They are:
Valid parameter beep

One 1 KHz tone (e.g. 1#)

Code accepted 

Five 1 KHz tones (e.g. 1#0#)

Error beep

Three 400 Hz tones (e.g. 80#)

Содержание M-20 Repeater Maker plus























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды