CertainTeed Bufftech Скачать руководство пользователя страница 36

Страница: 36 / 60

Privacy Fence –

Chesterfield with Huntington Accent, Chesterfield with Westminster Accent

1. Getting Started

• Be sure to call underground (811) prior to digging

• Assemble gates (if necessary) and decide where they will

be located

• Stake out the fence line

• Space and mark post hole locations for gate and sections

(spacer bar/template may be useful)

• Start at gate end post and work outward to determine

proper fence height relative to ground

2. Dig Holes

• Dig holes 30" deep or to frost line

- Hole size for 5 x 5 posts = approximately 12"

• Clean holes and check for straight walls

• Bell bottom of holes

3. Install First Post

• Insert post in hole

• Determine rough height

• Fill hole around post with concrete mix (sand, gravel and

cement) approximately 2" or 4" below grade

• Tamp concrete in hole to eliminate air pockets

• Level and square post

4. Install Bottom Rail

• Tape the ends of any rail being inserted into a post that is to

be filled with concrete to prevent concrete seepage

• Insert lock ring in each end of rail

• Depress lock ring tabs and insert rail in post. Tabs will recoil

to hold rail in post

5. Install Second Post

• Insert second post in hole

• Insert bottom rail in post

• Insert block under bottom rail to position at correct

fence height

• Fill hole around second post with concrete mix

• Tamp, level and square fence

• Assembly may be continued by installing all bottom rails first,

or one section at a time

6. Support and Secure

• Level and square fence

• To lower a post, place a wood block from corner to corner on

the post and carefully tap with a mallet

• Never strike the PVC post without a wood support

7. Picket End Channel

• Cut end channel to length

• Center channel on post between routed holes

• Attach channel to post in four locations

8. Install Pickets and Rails

• Insert pickets in bottom rail

• Insert top rail over pickets

• Insert lock ring in each end of rail

• Depress lock rings tabs, insert top rail in post

9. Install Accents

• Huntington

- Insert top 2 x 3-1/2 rail with larger holes facing down

into post

- Insert pickets through rail and lock into top fence section rail

(pickets are factory crimped to hold in place)

- To create desired scalloped effect, longer length pickets will

need to be cut and then crimped, or a bullet clip may be

inserted to hold picket in rail

• Westminster

- Insert bottom and side channels (overlap ends) into position

on rail and posts - secure with #8 x 1-1/2" screws

- Insert lattice into channels

- Slide top channel over lattice

- Insert top 2 x 3-1/2 rail into routed post holes

- Secure top channel 2 x 3-1/2 top rail with #8 x 1-1/2" screws

10. Hang Gate/Install Hardware

• For complete details, see gate installation instructions in

hardware box

• Position gate between posts

• Allow 1" gap for hinge and 3/4" for latch and gate swing

• Block up gate to square with fence; rails should be level

• Gate hardware must be secured to two sides of the post

11. Solidify Gate Posts

• It is critical that gate hinge and latch posts are solid to ensure

proper gate functionality. Two methods are available:

A. Aluminum gate post stiffener

- Slide aluminum gate stiffener inside hinge,

latch or end posts

- Drive a screw through the vinyl into the aluminum

stiffener at the bottom of the post

- Insert post into the ground

- Fill hole with concrete around outside of post

B. Concrete and rebar*

- Use two pieces of 1/2" rebar in each hinge, latch and

end post

- Rebar should extend from the bottom of the hole to

approximately 12" from the top of the post

- Hold rebar in opposite corners of post with rebar

separator clips

- Fill post with concrete mix to cover rebar and

hardware fasteners

- Tamp post with a rubber mallet to eliminate air pockets

- Leave gate on blocks for 72 hours to allow concrete to set

12. Install Caps

• Install post caps

• Caps may be secured with glue, silicone adhesive or

#8 x 1-1/2" screws, caps and washers

* Caution – In climates that experience freeze-thaw cycles, this installation method could result in post cracking over time. This would not be covered by the warranty.

Содержание Bufftech





























































Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды

CertainTeed Bufftech, Инструкция по сборке и установке

Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды