CertainTeed Bufftech Скачать руководство пользователя страница 28

Страница: 28 / 60

Privacy Fence –

Sherwood 4' and 6' High

1. Getting Started

• Be sure to call underground (811) prior to digging

• Determine gate location(s)

• Stake out the fence line

• Space and mark post hole locations for gate and sections

(spacer bar/template may be useful)

• Start at an end, gate, or corner post and work outward to

determine proper fence height relative to ground. If there is

a slope it is easier to begin at the top end and work your

way downhill

2. Dig Holes

• Dig holes 48" deep

- Hole size for 5 x 5 posts = approximately 12"

• Clean holes and check for straight walls

• Bell bottom of holes

3. Install Panel Brackets (note brackets

come attached to the tip of fence
posts)

• Determine height of bracket from top of post

• Attach bracket to post with #14 hex washer head self-

tapping screw

NOTE: Put the screw through the hole as close to the top as

you are able

• A template can speed attachment for level installations

4. Cutting Down Posts (if required)

• Measure height from top of post

• Cut off bottom of post with metal cutting blade

• Never cut the top of the post

5. Setting Posts

• Insert post and hole

• Determine rough height

• Fill hole around post with concrete mix (sand, gravel and

cement) approximately 2" or 4" below grade

• Tamp concrete in hole to eliminate air pockets

• Level and square post

6. Spacing Posts (See page 29 for post

centers)

• Use steel stiffener from panel to ensure panels will level

• Place stiffener between posts.

• Set post (leave spacer in place for one hour minimum)

ProTip: create your own template/space to ensure post spacing.
6'x 6'= 70-3/4"

4'x 8'= 95"

7. Install Fence Panels

• Check to ensure top and bottom rails have stiffeners. They

come installed, however may have been removed to use as

spacers when setting posts

• Lift panel to approximately 4’ off ground

• Insert panel into channel on first post

• Flex the next post until the channel will receive panel

• Ease panel down onto fence brackets

• Level panel

8. Secure Fence Panels

• Panels must be attached to end, gate, and corner post with

one fastener per panel

• To prevent unauthorized panel removal, you can attach one

end of each panel into the post with one fastener

• Never attach both ends of a panel to posts

9. Cutting Panels (if required)

• Remove steel stiffeners from panel

• Determine distance between posts from inside of channel to

inside of channel

• Cut stiffeners to that width

• Measure and mark panel ½" shorter than stiffeners (this is

needed for expansion and contraction of panel)

• Cut panel

NOTE: 6 ft panel includes vertical steel insert in center of panel.

10. Gate Openings

• Post spacing is critical. The ideal spacing is 1" on latch post

and 1-1/2" between hinge post

• Hinges should be attached to a gate post

11. Gate Installation

• First, attach striker bar to gate using provide button head screws

• Thread the ½" hinge rod into the upper and lower inserts in

the metal gate frame leaving approximately 1-1/2" from the

edge of the gate to the bracket.

• Determine proper height for gate and block up gate square

with fence

• Attach hinges to gate post with 2-1/2" self-tapping screws

provided (do not over tighten screws as this can crush the

internal foam and make an indentation in the post

• Level the gate

• Align the latch with the striker bar and attach the latch to

end post with 2-1/2" self-tapping screws provided.

12. Install Caps

• Install post caps (caps are pressure fit, however a 3" deck

screw can be driven through the top of the cap into the

middle of the post if desired)

Содержание Bufftech





























































Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды

CertainTeed Bufftech, Инструкция по сборке и установке

Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды