CertainTeed 48P-6-19 Скачать руководство пользователя страница 7

7 | 

P a g e

 

 

WARNING: DO NOT SMOKE WHEN OPERATING THE MACHINE. 

 

WARNING: DO NOT SMOKE OR BE NEAR ANY FLAME WHILE REFUELING THE GAS TANK. DO 
NOT  FILL  TANK  WHILE  THE  ENGINE  IS  RUNNING  OR  HOT.    FUMES  FROM  FUEL  ARE 
EXPLOSIVE AND CAN BE FATAL. FOLLOW ALL SAFETY PROCAUTIONS WHEN HANDLING ANY 
TYPE OF FUEL. 

 

WARNING:  CARBON  MONOXIDE  POISIONING  FROM  ENGINE  EXHAUST  CAN  BE  FATAL. 
MAKE SURE TO OPERATE THE MACHINE IN A WELL VENTILATED AREA. 

 

WARNING:  ALWAYS  OPERATE  THE  VAC-MATIC

TM

  19  MACHINE  ON  A  LEVEL  SURFACE.  

OPERATING THE MACHINE WHEN IT IS NOT LEVEL COULD LEAD TO ENGINE FAILURE OR THE 
MACHINE TIPPING OVER. 

 

 

 

UPON COMPLETION OF THE JOB 

1.

 

Make sure vacuum hose is empty. 

2.

 

Move throttle to slow position and allow engine to run for several minutes. 

3.

 

Turn engine off. 

4.

 

Wait for machine to completely stop rotating. 

5.

 

Remove hoses and or containment bag from machine. 

 

WARNING: NEVER REPLACE A CONTAINMENT BAG WHILE THE ENGINE IS ON. ALWAYS SHUT 
DOWN  THE  ENGINE  AND  REMOVE  THE  KEY  FROM  THE  IGNITION  WHEN  CHANGING  BAGS.  
NEVER REMOVE OR REPLACE HOSES WHILE THE ENGINE IS ON. 

 

WARNING: FAILURE TO WAIT FOR MACHINE TO COMPLETELY STOP BEFORE REMOVING HOSES 
OR CONTAINMENT BAG MAY RESULT IN SERIOUS INJURY. 

 

 

Содержание 48P-6-19












Отзывы: