Certa CTPTDCSAWA Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 40

Certa CTPTDCSAWA Скачать руководство пользователя страница 27

Maintenance:

•

Before performing maintenance work, switch off the Certa Petrol Demolition

Concrete Saw and pull out the plug cap.

•

Allow the Certa Petrol Demolition Concrete Saw to cool off before doing any

maintenance work (burn hazard)!

•

Always check the Certa Petrol Demolition Concrete Saw before use to ensure that

it is in good working order. Check that the cutting disc is properly mounted, and

that the cutting wheel is undamaged and suitable for the job it will be used for.

•

Operate the Certa Petrol Demolition Concrete Saw only at a low noise and

emission level. For this, ensure the carburettor is adjusted correctly.

•

Clean the Certa Petrol Demolition Concrete Saw regularly.

•

Check the fuel lank cap regularly for good sealing.

Observe the accident prevention instructions issued by trade associations and insurance

companies.

NEVER

perform any modifications to the Certa Petrol Demolition Concrete

Saw. You will only be putting your safety at risk!
Perform only the general maintenance and repair works described in the user guide. All other

work must be carried out by an approved Kogan.com service representative.
Use only original spares and accessories. The use of non-original spares, accessories or

cutting disc sin creases the risk of an accident. It cannot accept any responsibility for

accidents or damage occurring in association with the use of cutting discs or accessories

other than the original.

Disposal and environmental protection

Be mindful of the environment!
Dispose of worn-out or defective cutting discs by your local disposal regulations. To protect

unusable cutting discs from misuse, destroy them before disposal.
When the Certa Petrol Demolition Concrete Saw is worn out or damaged beyond repair,

have it disposed of or recycled in an environmentally sound manner. If necessary, consult

your local council for more information.

Service

For correct adjustment of the idling speed, the following steps must be carried out:

•

Start the engine and run it until it is warm (about 3- 5 minutes).

•

Adjust the carburettor with the screwdriver (7) included with the Certa Petrol

Demolition Concrete Saw. It has a lug that helps with adjustment.

«
...
25
26
27
28
29
...
»

Содержание CTPTDCSAWA









































Отзывы:

Нет отзывов