Certa CTPTDCSAWA Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 40

Certa CTPTDCSAWA Скачать руководство пользователя страница 24

•

Grasp front handles firmly with one hand and press the Certa Petrol Demolition

Concrete Saw against the ground.

•

Place left toe in the rear hand guard.

•

Move the flameout switch (3) up (into choke position). This also activates the half-

throttle lock.

•

Pull the starter handle smoothly and evenly, until you hear the first ignition (max. 3-

5 pulls).

Caution:

Do not pull the starter cable more than about 50 cm out, and let it back in slowly

by hand. Move the flameout switch (3) to the central ON position Pull the starter handle

smoothly and evenly again.
As soon as the engine is running grasp the rear handle (the Trigger control (5) is activated by

the palm) and press the throttle trigger (4). The half-throttle lock will disengage and the

engine will now idle.

Warm starting:

As described above for cold starting, but before starting push the flameout switch (3) up

(Choke position) and then right away back to the middle “ON” position. This is only to

engage the half-throttle lock. If the engine doesn't start after 2 or 3 pulls, repeat the entire

starting procedure as described for cold starting.

Note:

If the engine was switched off only for a short time, the saw can be started without

using the flameout switch.

Stopping the engine

Depress the combination switch

(3).

Note:

After being pressed down, the combination switch will revert to the “on” position

again. The engine is switched off but can be turned on again without moving the

combination switch.

Engine off

Warm Start (ON)

Cold Start (Choke)

1.

Starter

2.

Fuel tank cap

3.

Flameout switch

4.

Trigger

5.

Trigger control

6.

Choke

«
...
22
23
24
25
26
...
»

Содержание CTPTDCSAWA









































Отзывы:

Нет отзывов