background image

 

DF Touch 

Page 17 of 32 

 

Notes

1.

 

A system running on battery power can be shut down by pressing 
the reset button which is located along the bottom edge of the 
unit. This button can be pressed using a paper clip or small 
screwdriver. 
 

2.

 

If operation on battery power is attempted before the battery 
reaches full charge, there may be insufficient voltage to transition 
to battery powered operation and the system will stop operating. 
Place the system back on AC/DC wall adapter or PoE power. Press 
the reset button if necessary to shut it down. 

 

Reset switch location 

9

 

CAMERA USE APPLICATION NOTES 

The following best practices are recommended for recording punches 
using camera validation: 

 

The puncher

s face should be well lit and be between 18 and 30 

inches from the camera lens (which is on the top center of the 
screen).    

 

There should not be any other faces in the view of the camera 
because the software will then not be able to decide which face 
to capture. 

 

There should not be a lot of movement behind the puncher.  
For this reason, the clock should not be mounted in busy areas 
if the camera function is to be used.  

 

There should not be a light source in the 

camera’s view

There are two camera validation options: 

Содержание Dayforce Touch Clock

































Отзывы: