9
Starting with the inside race, apply
threadlock and attach two short balls
(
Tip 1
) directly across from each
other, similarly attach two medium
balls to the remaining holes. Attach
three short balls (
Tip 2
) to the outside
race, each 120 degrees apart. The
extra location is used for the anti-
rotation bracket assembled later.
Step 8 Swashplate Assembly
Before starting, carefully apply two or three drops of CA to the seam between the top and bottom oilite bushings and
the plastic washout hub. Do not get any adhesive on the inside surfaces that will slide against the main shaft. Let dry
completely.
Attach two Medium Balls (
Tip 2
) to the Washout Mixing Arms (
Note, attach from the flat side of the
arm
).
R30
using one slide tube inserted from the flat side and secured using one 3x16mm Button Head Screw
and one 3x7mm Flat Washer per arm.
R50
Press one 3x7mm Ball Bearing into one side followed by one
3x5mm spacer and one more bearing from the opposite side. Slide one M3x16 Button Head Screw through the
bearings in the arm and slide one 3x5x0.5 washer between the bearing before tightening into the washout hub.
Note, the screw is attached on the left when installed later on the main shaft. Press the radius link on to the
inner short balls on the Swashplate.
STEP 7 Washout Assembly
Radius Link &
M2x12 Pin
[HI3152A]
M3x16 Button
Head Screw
3x7 Ball
Bearing x 2
[CNBB0730]
Medium
Ball x 2
[CNLR1015]
Washout Hub
[HI3152C]
3x5x0.5
Micro Washer
[CNLR1003]
Washout Arm x 2
[HI3152C]
Oilite
Bushing
M3x7 Flat
Washer x 2
Oilite
Bearing
Slide Tube
x 2
R-50
R-30
M3x5x3
Spacer
Washout
Assembly
[HI3152C]
Swashplate
Assembly
[HI6146]
Short Silver
Ball x 5
[CNLR1014]
Medium Silver
Ball x 2
[CNLR1015]
Short
Silver Ball
Install Anti
Rotation
Pin Later
The Canopy has a line molded into the plastic to follow when trimming the windshield part out, be
careful, trim the innermost line leaving the 6mm band for attaching the windshield. Using a sharp hobby knife
carefully scribe a line several times into the plastic until you cut through the material. Similarly trim the clear
windshield along the provided line, to make it easier to see the line, use a non-permanent marker and trace the
line, any extra ink can be removed with rubbing alcohol. Test fit the canopy together by taping it to the canopy,
some additional trimming maybe necessary to get a good fit. From Bag 5, the inside canopy mount can be
installed (
note the direction of the mount
) with two 3x6mm Self Tapping Screws,(
note: the location for
the mount has to be moved 8mm forward of the marked location on the bottom of the canopy
). The clear
windshield can be attached using six 2x6mm Self Tapping Screws in Bag 4, drill six 1mm holes at the locations
shown.
The two holes for the rear canopy mount have to be
close the rear and
bottom edge as shown
and attach the two rubber mount on canopy.
HI3130B
HI3133A
M3x8 Self Tapping Screw x 2
Inside Canopy
Mount [HI3129]
M2x6 Self
Tapping
Screws x 6
To inprove the adhesion of the decals to the body, peel the decal off the backing and apply one coat
of spray adhesive (spray glue) to the sticky side, commonly found in your hobbyshop. For those who
would prefer to paint the canopy.
Step 46 Canopy & Decals
Raven 30/50 decal [HI3131J]
Step 47 Canopy Mounts
Rubber Mount
Right Horizontal Fins
Right Side Vertical Fin
Right Side Canopy
Left Side Canopy
Left Horizontal Fins
Left Side Canopy
Left Horizontal Fins
Leftt Side Vertical Fin
