Century Helicopter Products Predator 60 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

background image

Install the rear ccpm lever into the upper frames flush with
the bearing on the left side, having the mount extend out the
right side frame. Assemble the upper frames but do not use
locktight at this time.

#HI6031
CCPM
Cyclic
Bellcranks

#HI6110
Upper Side Frames
Left & Right

#HI6032
Rear CCPM Lever

#CNLR1014
Short Ball

#CNLR1020
Medium
Ball

M3x30

Socket Screw

#HW6000

Stepped
Standoff

26mm
Threaded
Spacer

The stepped standoff is positioned with the step against the
ball bearing in the ccpm bellcrank. Correct orientation has the
two symmetric steel ball facing outwards and the obtuse angle
towards the swashplate.

#CNBB37

Apply locktight to the threads on the inside standoff, insert
between the frames and attach the ccpm cyclic bellcranks
being careful to observe the correct direction. For 140
Degree ccpm setup, move bellcranks to forward holes.

M3x30
Socket Screw
#HW6000

120 Degree
CCPM Setup

Press the rear ccpm lever onto the mount that sticks out of the
right side of the upper frames with the steel ball downwards.
Secure with the M3 button head screw.

M3x10 Button
Head Screw

#CNLR1014
Short Ball

#HW6112A

Vertical Front

Frame

#HI6020

Cooling Fan

Mount

M3x8 Self Tap Screw (from behind)

8.45:1
only !

Attach the front cooling fan mount to the vertical front frame
inserting the M3 screw from the flat side of the frame. Note:
8.45:1 gear ratio requires the shroud mount hole to be modified.

#HW6127

Front Frame
Standoff Set

Ensure that the correct standoffs are used in the correct
locations. The 26mm threaded hex standoffs are not shown.

#HW6127A
Rear Frame
Standoff Set

X-Frame x 2

15mm Servo
Frames x 4

17mm Rear
Frames x 4

26mm Threaded
Standoffs x 2

26

29

30

7

28

27

25

«
...
5
6
7
8
9
...
»

Содержание Predator 60





















Отзывы:

Нет отзывов

Похожие инструкции для Predator 60

Traffic Light-Grand

Бренд: Jamara Страницы: 4

Mercedes-Benz Arocs

Бренд: Jamara Страницы: 4

Mercedes-AMG GT

Бренд: Jamara Страницы: 8

Liebherr 2,4 GHz

Бренд: Jamara Страницы: 8

Бренд: Jamara Страницы: 20

Beaver DHC 2 V2

Бренд: Jamara Страницы: 24

Бренд: Jamara Страницы: 16

Бренд: Jamara Страницы: 8

Бренд: T&J Страницы: 11

K-FORCE Build and Blast 47518

Бренд: K'Nex Страницы: 2

Бренд: Minicraft Models Страницы: 4

Бренд: marklin Страницы: 24

Sd.Kfz.251/1 Ausf.B

Бренд: REVELL Страницы: 7

Бренд: Eduard Страницы: 4

Ju 88C-6b Night Fighter exterior

Бренд: Eduard Страницы: 6

BN TWIN HIGHCHAIR

Бренд: Smoby Страницы: 4

VOICE TECH RESCUE HEROES Wendy Waters Firefighter

Бренд: Fisher-Price Страницы: 2

Бренд: FMS Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды