Century Helicopter Products Predator 60 Скачать руководство пользователя страница 3

Страница: 3 / 20

#HI6160
Rotor Head
Block

#HI6181
Head Damping
O-Rings

Press in the damping o-rings into the rotor head block.
Lubricate with light oil.

#CN2215A
Silver Head Button

Bond the threaded stud into the head button using permanent
locktight then apply more permanent locktight and bond into
the top of the rotor head block.

SE & Max

only

Assemble the seesaw part around the rotor head block. Bond
the bearing cups to the metal offset plates.

#HI3167B
Offset Plates

#HI3167F
Bearing Cups

#HI3167G
Tie Bars &
Spacers

#CNBB37

#CNBB48

#HI6167
Special Ball

Make sure that the steel ball is mounted on the left when on
the rotor head.

Steel Ball on
Left side.

The washout guide should be positioned against the rotor head
block, with the pins aligned parallel to the feathering spindle.

#HI6153
Washout
Guide

#HI6189
Bell Mixing
Arm

M3x15 Button
Head Screw
#HW6001

M3x6

Button Head

Screw

M3x4 Set
Screw

Press the M3x7 Flanged bearings into the seesaw capturing
one steel spacer in between. Attach to the blade grip with the
special shoulder bolt.

M3x18 Special
Shoulder Bolt
#HW6001

#CNBB37F

#CNLR1014
Short Ball

#CNLR1020
Medium Ball

1:1

1:1.3 3D & Sport
1:1.6 Sport & FAI

Bell Mixer Ratios

Содержание Predator 60





















Результаты поиска

Содержание Predator 60

Отзывы:

Похожие инструкции для Predator 60

Бренды по названию

Популярные бренды

Century Helicopter Products Predator 60, Инструкция по эксплуатации

Результаты поиска

Содержание Predator 60

Отзывы:

Похожие инструкции для Predator 60

Бренды по названию

Популярные бренды