background image

2191

JDV28 cover

12/10/99  djt

INSTALLER / CONSUMER 

SAFETY INFORMATION

30004177  3/08  Rev. 2

PLEASE READ THIS MANUAL 
BEFORE INSTALLING AND USING 
APPLIANCE.

WARNING!

IF THE INFORMATION IN THIS 
MANUAL IS NOT FOLLOWED 
EXACTLY, A FIRE OR EXPLOSION 
MAY RESULT CAUSING 
PROPERTY DAMAGE, PERSONAL 
INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY

Installation and service must be 
performed by a qualified installer, 
service agency or the gas suppler.

WHAT TO DO IF 

YOU SMELL GAS:

• 

Do not try to light any appliance.

• 

Do not touch any electric switch; do 
not use any phone in your building.

• 

Immediately call your gas supplier 
from your neighbor’s phone. Follow 
the gas supplier’s instructions.

• 

If you cannot reach your gas supplier, 
call the fire department.

DO NOT STORE OR USE 
GASOLINE OR OTHER 
FLAMMABLE VAPORS AND 
LIQUIDS IN THE VICINITY OF THIS 
OR ANY OTHER APPLIANCE.

This appliance may be installed in an 
after market permanently located 
manufactured (mobile) home where not 
prohibited by local codes.

This appliance is only for use with the 
type of gas indicated on the rating plate.

This appliance is not convertible for use 
with other gases unless a certified kit is 
used.

Jefferson
Direct Vent/Natural Vent 
Gas Heater

Model: JDVBRN

Homeowner’s Installation 

and Operating Manual

CERTIFIED

DESIGN

CERTIFIED

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Содержание JDVBRN









































Отзывы: