manualshive.com logo in svg

Centurion SD04, Руководство по установке

Поделиться
Скачать
Centurion SD04 Скачать руководство пользователя страница 23

page 23

www.centsys.com

OPERA

TOR

 INS
TALLATION

S

ECTION

 6

FIGURE 29

FIGURE 30

FIGURE 31

Level the 

SDO4

 again, and measure 

the length needed from the ceiling 

to the underside of the drive rail, 

marked as ‘Value Xmm’ in Figure 29.

Drive rail 

hanger nut

Drive rail 

hanger bolt

SDO4

Drive rail hanger 

bracket 

Punched 

angle iron

Remove the two drive rail hanger 

nuts from the bolts, and locate the 

two lengths of punched angle iron 

into position as shown in Figure 31.

Secure them in position with the two 

drive rail hanger nuts.

Ensure that the punched 

angle iron does not 

protrude further than the 

SDO4 drive rail base,  

as this will interfere 

with the operation of the 

motor!

Spirit level

Mounted punched 

angle iron

Ceiling

Value Xmm

SDO4

Drive Rail

Two equal 

lengths 

of punched 

angle iron

Value Xmm

Value Xmm

Using an angle grinder or hack saw, 

cut two lengths of punched angle 

iron to the measurement taken for 

‘Value Xmm’.

Snip off the four corners of 

the punched angle iron to 

add a degree of safety and 

neatness to the installation. 

Содержание SD04

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды