CentraLine HAWK 8000 Скачать руководство пользователя страница 7

HAWK 8000 CONTROLLER – BACKUP & RESTORE GUIDE 

 7 

EN2Z-1027GE51 

R0517 

The restore begins. 

 

  CAUTION 

Risk of equipment damage! 

 

Once a restore begins, do not interrupt the process by removing the USB flash drive, disconnecting the 
power, or pressing the backup and restore button again. If you do not allow the restore to complete, the 
controller could be left in a non-functional state. 

 

When the restore successfully completes, the backup and restore LED turns OFF and the system displays 
a message indicating that the restore is complete and that the controller requires a reset. 

Step 12:  Turn the controller's power OFF and back ON again. 

 

Restoring Factory Defaults 

The process of restoring factory defaults returns the HAWK 8000 to the state it was in when it shipped from the 
factory. This procedure describes the steps to restore factory defaults when using a terminal emulator program to 
access the controller's system shell menu. 

Prerequisites: 

•  A USB-to-Micro USB cable (same cable as that used to connect a smart phone to a computer) connecting the 

HAWK 8000 to your PC. The Debug port on a HAWK 8000 is a standard Micro-A type USB port for debugging 
serial communications. 

•  A terminal emulator (system shell program), such as PuTTY, installed on your PC. 
 

  CAUTION 

Risk of equipment damage!

 

 

Recovering factory defaults removes all platform and station data in the HAWK 8000. Be sure to backup data prior 
to performing this procedure. 

 
The following are a few scenarios for which you might choose to restore factory defaults: 
•  While commissioning a brand new HAWK 8000, you make an error entering the default platform daemon 

credentials or passphrase. The result is that you cannot commission the HAWK 8000. In this scenario, your only 
recovery option is to restore the factory defaults. 

•  When decommissioning the HAWK 8000, a best practice to follow is recovering the factory defaults in order to 

wipe all of the platform and station data in the HAWK 8000. 

Fig. 2 indicates the position of USB ports and pushbuttons behind the access door. 

Содержание HAWK 8000












Отзывы: